Bedienungsanleitung Cateye MSC-CY300 (Seite 71 von 83) (Englisch)

473082

Zoom out

Zoom in

Vorherige Seite

1/83

Nächste Seite

ENG-70

Trouble on operation

Trouble Check Items Remedy

Pressing and holding the

MODE1 or MODE2 button

does not turn on a light.

Check whether the Setup

mode is displayed (page 49).

The backlight does not turn on in the Setup

mode.

Check whether

lights up

on the wristwatch screen.

The remaining battery capacity of the wristwatch

is low. Replace it with a new battery (CR2430).

After replacement, be sure to perform the restart-

ing operation (page 14).

Pressing the SSS button

does not start/stop mea-

surement.

Check whether the auto-mode

is turned on (with

illumi-

nating).

When the auto-mode is on ( icon appears),

you cannot start or stop the measurement by

pressing the button. To start/stop measurement

by pressing the SSS button, switch the auto-

mode to off (page 58).

The heart rate sensor

(speed sensor) ID check

failed.

The battery for the heart rate sensor (speed

sensor) is possibly depleted. After replacing the

battery with a new one (CR2032), check the

sensor ID again (page 53).

Lap data cannot be stored. Check whether “--” appears

for the Lap No. screen.

The data volume exceeds the wristwatch mem-

ory capacity. Delete the ﬁles (page 45).

When using the optional “USB communication *

kit”, delete the ﬁles after you send the saved

ﬁles to your PC.

Does the lap time exceed 100

hours (or the interval distance

exceed 9999.99 km/mile) ?

Laps cannot be measured, if recordable range

described on the left is exceeded. Reset the data

(page 27), and then perform measurement again.

Is it immediately after press-

ing the LAP button?

Recording laps needs at least 5 seconds of in-

terval.

Abnormal values appear.

Are there any objects emitting

electromagnetic waves (railway

tracks, transmitting stations

for television, etc.) nearby?

Keep the unit away from any object that may be

causing interference, and reset the data (page

27).

Any setting cannot be

changed in Option mode or

Setup mode.

Is it during measurement? Settings can be only viewed during the measure-

ment.

Check whether the auto-mode

is on (

lights up).

When the auto-mode is on ( lights up), the

wristwatch may enter measurement mode due

to electromagnetic waves. Keep the unit away

from any object that may be causing interference

with electromagnetic waves.

Check whether “DATA RESET”

is displayed.

To change the target heart rate zone, measure-

ment unit, and record interval, the resetting

operation is required. Stop the measurement,

and perform the resetting operation (page 27).

The record data in the File

view cannot be viewed to

the end.

Check whether

“MEMORY FULL” is

displayed on the screen

during measurement.

The data volume exceeds the wristwatch mem-

ory capacity. The data was saved automatically

during measurement, and any subsequent data

was no longer recorded. Delete the ﬁles for

subsequent measurement (page 45).

When using the optional “USB communication *

kit”, delete the ﬁles after you send the saved

ﬁles to your PC.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cateye MSC-CY300 Seite 71

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cateye MSC-CY300

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info