Bedienungsanleitung Cateye V2c (Seite 8 von 21) (Englisch)

508115

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

ENG-15ENG-14

ENG

Average

speed

Average

cadence

Maximum

speed

Maximum

cadence

Current speed

Cadence

M1/+

M2/-

Date

Clock

Total time

Total distance

Elapsed time Trip distance

Countdown

distance

Lap

number

Lap timer

Average

lap

speed

Lap distance

(2 Sec.)

5. Selecting speed unit

Select the speed unit from “km” and “mile”.

1. Select the speed unit.

↔↔

↔ mile:

M1/+

M2/-

2. After selecting, press the MENU button. The measurement

screen appears and the computer set-up is completed.

6. Operation test

Test the functioning of the speed sensor (SPEED) and the cadence sensor (CADENCE).

* If the sensor signal icons,

, and are turned off, press the M1/+ or M2/- button

to turn them on.

Speed sensor (SPEED)

1. Raise the rear wheel and spin the wheel.

2. When

flashes on the computer screen and

the speed is displayed, it is operating normally.

Cadence sensor (CADENCE)

1. Turn the crank.

2. When

flashes on the computer screen

and the cadence is displayed, it is

operating normally.

* When or does not flash, the position of the sensor and the magnet is not

proper. Check and adjust the position of the sensor and magnet again (page 7).

Important:

In the following situations, it is possible that other sensor's ID was picked up;

(such can happen when performing ID Synch at the race venue or group rides)

• Does not display values, even though sensor/magnet position is proper

Recommended Action: Go to the computer's ID Synch setup screen

(page 23) and go through the process of ID Synch. (Make sure that here

is no similar devices in the vicinity. Signal transition distance can vary

from environmental conditions such as weather, buildings, etc)

Basic operation of the computer

Functions on the measurement screen

The measurement screen displays 4 different types of data, which are switched by press-

ing the M1/+ and M2/- buttons.

The display data are as follows.

Upper display data

Displays the data related to the speed.

Middle display data

Displays the data related to the cadence.

Lower display data

Displays the other data.

Real time lap data

(on-going lap data)

*Pressing and holding the M2/-

button while displaying the lap

timer switches the lap timer to the

lap distance. Pressing it again

returns to the lap timer.

* Upper and Middle display data are switched in sync together.

Switch using the M1/+ button

Switch using the M2/- button

(or)

Sensor signal status

If there is no incoming signal for approximately 5 minutes, the transmission stops

and no longer receive the sensor data. Once you press the M1/+ or M2/- button, the

computer will come out of the Sleep mode and return to the Stand-by for sensor

signal. Signal transmission status can be checked with Signal icon.

(flashing) : Receiving sensor signal (constant) : Stand-by for sensor signal

(off) : Transmission off

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cateye V2c Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cateye V2c

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info