Bedienungsanleitung Cateye V2c (Seite 15 von 21) (Englisch)

508115

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

ENG-29ENG-28

ENG

M2/- M1/+

1. Press the MENU button on the measurement screen to

switch to the menu top screen.

Switch to the SEnSOR-ID screen using the M1/+ and M2/-

buttons, and confirm with the SSE button.

Menu top:

Changing the menu:

M1/+

M2/-

Confirm:

SSE

2. Select the sensor ID to be checked.

Select “SP1 (speed sensor 1)” and “SP2 (speed sensor 2)”

using the M1/+ and M2/- buttons.

Selecting the sensor:

M1/+

M2/-

3. Check whether the speed/cadence is mounted properly.

4. Press the SSE button to start searching the ID.

When the speed (cadence) is displayed as “ID-OK” on the

screen by spinning the rear wheel or crank, synchronizing is

completed.

Start searching:

SSE

5. Pressing the MENU button returns to the menu top screen

(SEnSOR-ID screen), and confirm the change.

Pressing it again returns to the measurement screen.

To the menu top/measurement screen:

* This unit enters the search mode for 5 minutes after starting the ID synch.

While “ID-SKIP” is indicated, press the SSE button in the search mode to cancel

the ID synch, and “ID-SKIP” is displayed. Unless a sensor signal is received in 5

minutes, “ID-ERROR” is displayed.

When “ID-SKIP” or “ID-ERROR” is displayed, the ID has not been synchronized

properly. In such a case, the sensor ID retains the previous ID setup. Check

whether the speed/cadence is mounted properly, is mounted properly, before

you check the ID again.

* SP2 is used when a computer is commonly used for second bicycles. By synchro-

nizing the ID of the second bicycle equipped with a second speed/cadence sensor

and the computer with SP2, re-synchronizing the ID is not required every time you

move the computer between first and the second bike.

(or)

(Back)

Wheel selection and tire circumference

Switch the Wheel Size (A / B), and change the Tire Size (tire roll out length).

* For the tire size, see “Tire circumference” (page 12).

1. Press the MENU button in the measurement screen to

switch to the menu top screen.

Switch to the WHEEL screen using the M1/+ and M2/-

buttons, and confirm with the SSE button.

Menu top:

Changing the menu:

M1/+

M2/-

Confirm:

SSE

2. Select the Wheel Size “A” or “B” using the M1/+ and M2/-

buttons.

A ↔ B:

M1/+

M2/-

Confirm:

SSE

At this point if change of tire circumference is not necessary,

you can escape the setup by pressing the MENU button.

3. Enter the last 2 digits of the tire circumference for the wheel

selected in Step 1 using the M1/+ and M2/- buttons, and

confirm with the SSE button.

Then, enter the first 2 digits in the same way.

Increase/decrease:

M1/+

M2/-

Move digits:

SSE

4. Pressing the MENU button returns to the menu top screen

(WHEEL screen), and confirm the change(s).

Pressing it again returns to the measurement screen.

To the menu top/measurement screen:

Searching the sensor ID

Receive and check the ID signal transmitted from the speed/cadence.

* This unit requires the sensor ID.

The computer cannot receive the sensor signal unless the sensor ID is synchronized properly.

* To synchronize the sensor ID, be within 5m from the bicycle with a speed/cadence sensor mounted

properly (page 7).

* When searching the sensor ID, make sure no other sensors are in the area within 10 m radius.

It is also possible to press the Reset button on the Speed/Cadence sensor to intentionally turn

off the signal transmission from the sensor.

(or)

Wheel selection

Current wheel size

(or)

(Back)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cateye V2c Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cateye V2c

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info