Bedienungsanleitung Cateye V3 (Seite 8 von 23) (Englisch)

508116

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

ENG-15

ENG

ENG-14

6. Operation test

Test the functioning of the speed sensor (SPEED) and the cadence sensor (CADENCE).

* If the sensor signal icons,

, and are turned off, press the M1/+ or M2/- button to

turn them on.

Speed sensor (SPEED)

1. Raise the rear wheel and spin the wheel.

2. When

flashes on the computer screen

and the speed is displayed, it is operating

normally.

Cadence sensor (CADENCE)

1. Turn the crank.

2. When

flashes on the computer screen

and the cadence is displayed, it is

operating normally.

* When or does not flash, the position of the sensor and the magnet is not

proper. Check and adjust the position of the sensor and magnet again (page 7).

Important: In the following situations, it is possible that other sensor's ID was picked

up; (such can happen when performing ID Synch at the race venue or

group rides)

• Does not display values, even though sensor/magnet position is proper

• Does not display HR values, even though HR sensor is strapped properly

Recommended Action: Go to the computer's ID Synch setup screen

(page 23) and go through the process of ID Synch. (Make sure that here

is no similar devices in the vicinity. Signal transition distance can vary

from environmental conditions such as weather, buildings, etc)

3. Verify that the speed/cadence sensor is mounted properly to

the bicycle.

4. Press the SSE button to start searching the speed sensor ID.

When the speed (cadence) is displayed as “ID-OK” on the

screen by spinning the rear wheel or crank, searching is

completed.

Start searching:

SSE

5. Press the MENU button to proceed to “Selecting speed unit”

below.

To “Selecting speed unit”:

* This unit enters the search mode for 5 minutes after starting the ID check.

Press the SSE button during the search mode, then “ID-SKIP” is indicated and it

proceeds to “Selecting speed unit” screen below. Or, unless a sensor signal is

received in 5 minutes, “ID-ERROR” is indicated and it proceeds to “Selecting

speed unit” screen below.

When “ID-SKIP” or “ID-ERROR” is indicated, this unit is not ready for

measurement because the sensor ID has not been registered even though the

set-up is completed. Be sure to check the sensor ID from the menu screen

“Searching the sensor ID” (page 29).

5. Selecting speed unit

Select the speed unit from “km” and “mile”.

1. Select the speed unit.

↔↔

↔ mile:

M1/+

M2/-

2. After selecting, press the MENU button. The measurement

screen appears and the computer set-up is completed.

(or)

(Back)

Sensor signal status

If there is no incoming signal for approximately 5 minutes, the transmission stops

and no longer receive the sensor data.

Once you press the M1/+ or M2/- button, the computer will come out of the Sleep

mode and return to the Stand-by for sensor signal.

Signal transmission status can be checked with Signal icon.

(flashing) : Receiving sensor signal

(constant) : Stand-by for sensor signal

(off) : Transmission off

* Transmission off status is independent for heart rate and speed/cadence sensor.

If both sensors stop transmission, the computer screen will change to Sleep

mode (page 17).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cateye V3 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cateye V3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info