Bedienungsanleitung Cateye Velo8 (Seite 1 von 2) (Englisch)

445222

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Caution

• Do not concentrate on the computer operations while riding. Always be sure to ride safety.

• Be sure to securely mount the magnet, sensor and bracket on your bicycle, and periodically check to see if any

parts have loosened.

• Used batteries are harmful if swallowed by mistake. They must be disposed in accordance with local regulations.

• Do not leave the main unit exposed to direct sunlight. Never disassemble the main unit.

• For cleaning of the main unit or accessories, use diluted neutral detergent on a soft cloth, and then wipe it off with

a dry cloth. Do not use paint thinner, benzine or alcohol since such chemicals may damage the surface.

Package Contents

1 Bracket

2 Wire

3 Sensor

4 Magnet

5 Nylon Ties 7

IMPORTANT!

Correct positions of the sensor and the magnet:

When rotating the front wheel, the magnet's 4 center must be aligned with the sensor's 3 marking line.

The distance between the sensor 3 and the magnet 4 must be less than 5mm.

Name of Parts

Speed 0.0 (4.0) to 299.9 km/h [0.0 (3.0) to 185.0 mph]

Mode Symbol Indicates the mode currently selected.

(The corresponding value is indicated on the lower line.)

Pace Arrow* Indicates if the current speed is faster or slower than the average speed.

(

Faster Slower)

Speed Scale

Sub Display (selected function)

Battery Case Cover

Contact

*The Pace Arrow feature is only available on the VELO8. Pace Arrows are not displayed on the VELO5.

Display function

• Tm* [Elapsed Time] 0:00'00" to 9:59'59"

• Dst [Trip Distance] 0.00 to 999.99 km [mile]

• Av* [Average Speed]

0.0 to 299.9 km/h [ 0.0 to 185.0 mph]

(Measurable up to 27 hrs or 999.99 km/h)

•

Mx [Maximum Speed] 0.0 (4.0) to 299.9 km/h [0.0(3.0) to 185.0 mph]

• Cal*

[Calorie Consumption]

0.0 to 9999.9 kcal (estimated from speed data)

• Odo [Total Distance] 0.0 to 9999.9 km [mile]

• [Clock] 0:00' to 23:59'[1:00'to 12:59']

This feature is only available on the VELO8. No measurement is done on the VELO5.

Start/Stop of Measuring

The unit starts measuring automatically when you start pedaling, and stops measuring when your come to a stop.

The upper display always shows the Current Speed.

Shift of Lower Display

Each time you press the MODE button, a different data value appears on the lower line.

Power Saving Function

If the main unit does not receive a signal after about 10 minutes, the main unit enters Power Saving Mode and

displays the clock count only. To re turn to normal display, press the MODE button or start your bicycle again to

cancel the Power Saving function.

Data Reset

When a screen with the

Reset

mark in the OPERATION FLOW is displayed, continue pressing the MODE button

and the measured data will return to zero. However, the Odometer (total distance) and Clock do not return to zero.

How to Set Clock

In the clock mode, press SET button on the back, and the display enters clock setting mode.

*If Km/h has been selected for speed scale, it becomes 24-hour clock.

If mph has been selected, it becomes 12-hour clock.

How to Change Tire Size

Display the Total Distance (Odo) and press the SET button to change the tire size. You can select a tire size in two

ways: Either select from among preset sizes

or enter the tire’s circumference directly in increments of 1 cm.

Maintenance

• If the contact of the unit or the bracket gets wet, dry it off with a cloth. If they become rusty, it will cause speed

detection error.

• If the gaps between the buttons and the unit get clogged with mud or sand, wash them away with water.

Troubleshooting

No display.

Has the battery in the main unit run down?

Replace it with a new one.

Incorrect data appears.

Do all clear operation.

Current speed does not appear.(First, short-circuit the contact of the main unit a few times with a piece of metal. If current

speed appears, the main unit is working fine and the cause should be attributed to the bracket or the sensor.)

Is the clearance between the sensor and the magnet too large?

Are the magnet's center and the sensor's marking line aligned?

Re-adjust the positions of the magnet and the sensor. (The clearance should be less than 5mm.)

Is the cord broken?

Even if the outside of the cord looks normal, there could be damage.

Replace the bracket and sensor set with a new one.

Is there anything sticking on the contact of the main unit or the bracket?

Clean the contact with a cloth.

Current speed disappears when using in the rain.

Wipe any water or dirt from the contacts and apply a water repellent silicon grease. Do not apply standard grease,

as it may cause damage to the bracket.

Replacing Battery

If the screen becomes dim, it is the time to replace the battery.

*Insert a new lithium battery (CR2032) with the (+) mark facing up.

1 After replacing the battery, perform the all-clear operation. Follow SETTING to select the measurement unit & tire

size and set the clock display to the current time.

Specification

Battery ---------------------- Lithium Battery CR2032 x 1(battery life: approx. 3 years)

(*The life of the factory-loaded battery might be shorter than this.)

Microcomputer ------------- 4-bit 1-chip (Crystal controlled oscillator)

Display ---------------------- Liquid crystal display

Sensor ---------------------- No-contact magnetic sensor

Tire Sizes ------------------- Tire sizes of 16, 18, 20, 22, 24, 26, 700C, and 27 inches, or tire peripheral lengths from 100 to 299

cm (Initial value: 26 in.)

Working Temperature ------ 0°C - 40°C

Length of Wire ------------- 70cm

Dimension/Weight --------- 1-7/8" x 1-25/32" x 23/32" (48 x 45 x 18 mm) / 1.06 oz ( 30 g)

*The specifications and design are subject to change without notice.

CAT EYE VELO 8

VELO 8

CAT EYE VELO 5

VELO 5

MODE

SET

(on Back)

CAT EYE VELO5

CAT EYE VELO8

CYCLOCOMPUTER

Model CC-VL500/CC-VL800

English

U.S. Pat. Nos. 4642606, 5236759 and Pat. Pending

CCVL5/8-031030 066600280

CAT EYE VELO 5

INSTALLING THE UNIT

A B

5mm

2 3

SETTING

●Calorie Consumption *

(VELO8)

The calorie consumption data is only the accumulated value that is

calculated from the speed data of every second. It differs from the

actual consumed calorie.

km/h

Speed 10 km/h 20 km/h 30 km/h

Kcal per hour

67.3 kcal 244.5 kcal 641.6 kcal

mph

Speed 10 mph 20 mph 30 mph

Kcal per hour

155.2 kcal 768.2 kcal 2297.2 kcal

Click

Cateye Velo8 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cateye Velo8

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info