Bedienungsanleitung CAWI ElCom 7205 (Seite 1 von 7) (Englisch, Holländisch, Französisch)

622509

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

Operating Instruction CAWI Electronic Lock „ElCom“ 7205

1. General

Even though using this lock system is very easy, please read these operating instructions carefully and completely

before using the lock; this will help to avoid operating errors. These instructions refer to an electronic lock installed in a

high-security container such as a safe.

The green LED will blink to confirm each keypad entry. The time period between any two entries may not exceed 20

seconds as otherwise all previous entries will be cleared.

The keypad could be supplied with two differend keypad prints. (see Fig.1 and Fig.2)

Fig.1 Input of numerical acces code

e.g.

Fig.2 Input of alpha-numeric acces code

e.g. ROLF12

2. Opening the electronic lock

Enter the six-digit combination set at the factory by pressing buttons 1 – 2 – 3 – 4 – 5 – 6 or enter your own six-digit

combination.

Please note: Press the C button to correct your entry; in this case the entire combination will have to be entered again.

The green LED will light for about 6 seconds to indicate that the lock has been cleared for opening. At the same time,

the electronic lock will clear the mechanism for opening. The door to the safe can now be unlocked with the keypad lever

and opened using the fingertip grip. The electronic locking element is then locked again automatically after about 6

seconds; this is indicated by the red and green LEDs blinking once. The electronic lock is only secured when the keypad

lever is moved manually into its locked position.

3. Closing the electronic lock

Close the door to the safe and return the keypad lever to its locked position, moving it all the way to the mechanical stop.

The red cap must be completely concealed by the keypad lever. The green LED goes out at the same time to indicate

that the electronic lock has been mechanically secured in this position.

Please note: Try to operate the keypad lever to verify that the container is closed correctly and securely.

4. Response to erroneous entries

The red LED lights for about 3 seconds whenever an invalid combination is entered. The combination may now be

entered again. After the third consecutive incorrect entry, however, a 10-second time-out period starts; the keypad will

accept no entries during this period. This time-out period will be extended by 10 seconds following each subsequent

incorrect entry. The time-out periods cannot be interrupted with the ”C” button.

5. Correction with the C button

If you press the C button during the entry sequence, then the entire series of digits previously entered will be cancelled.

If a programming phase has been initiated, then the lock will exit the programming mode; you must re-start programming

from the very beginning by pressing the * button.

Exception: The time-out period following erroneous entries and the low-battery warning period cannot be interrupted by

pressing the C button.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

CAWI ElCom 7205 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von CAWI ElCom 7205

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info