Bedienungsanleitung Cecotec Conga 1790 vital (Seite 21 von 63) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

753600

Zoom out

Zoom in

Vorherige Seite

1/63

Nächste Seite

4140

ENGLISH ENGLISH

Pause

Press the power button on the robot to pause the cleaning process.

Press the power button on the robot to resume the cleaning process.

Fig. 21

Return to the charging base

Press the back home button on the robot in order to send the robot to the charging base.

Turn off

Long press the power button to turn the robot off.

Fig. 22

Warning: The robot vacuum cleaner has a power switch located on its main body. If the robot

is not going to be used for long periods of time, it is suggested to switch it off. If the robot is

switched off, it will restore factory default settings as a safety measure. The robot will only

carry out scheduled cleaning if it has been scheduled while the switch is ON, otherwise, it will

have to be scheduled again from the App.

Cleaning modes

This robot includes different modes and different functions that can be activated from the App.

Auto mode

Press the power button for the robot to start Auto cleaning mode.

The robot will clean the whole surface, edges, around objects such as tables, chairs etc. Once

it starts running out of battery, it will return to the charging base.

Fig. 23

Thorough Scrubbing mode

Attach the mop cloth to the water tank and fill the tank with water.

Install the Wet & dry tank in the robot and turn it on.

Fig. 24

Use the App to select the desired scrubbing power level: High, Medium or Low.

Once the scrubbing mode is selected, the device will perform the function “All in One” to

vacuum, mop, scrub and sweep at the same time thanks to its mixed tank.

Note: If you want to sweep the floor, skip the water-filling step.

To ensure perfect scrubbing from the start, it is suggested to dampen the mop cloth evenly

with water before use.

Spiral mode

The robot will carry out an intense cleaning of a specific area when this mode is activated.

The robot will start cleaning at a specific point and will move outwards performing spiral

movements (1 meter). Then, it will return to the starting point in spiral movements again.

Fig. 15

Direct exposure to sun light or great light contrasts may affect to the correct operating of the

sensors. If this happens and the robot stops, change it to a new location for it to start operating

again.

Place the charging base against the wall and leave a minimum free space of:

2 metres to the front.

1 metre to each side.

Fig. 16

Connect the charging base to a power supply. Wind and store the remaining cord in the lower

part of the charging base to avoid accidents.

Fig. 17

Install both side brushes in their corresponding slots, located on the robot’s bottom part. Press

until it clicks to make sure they are properly fixed.

Fig. 18

Press the power switch located on the bottom part of the robot. Make sure the power switch

is turned On.

Fig. 19

Place the robot on the charging base and make sure the charging terminals on the robot match

with those of the charging base. Once the robot is properly placed, it will beep once and the

power button will light up If the light blinks orange, it means the battery is not completely

charged. To ensure maximum cleaning time, wait until the light switches to steady blue. This

will indicate the battery is fully charged and that the robot is ready to clean.

Fig. 20

3. OPERATION

Start cleaning

Long press the power button on the robot to activate the robot up.

Press the power button on the robot to start cleaning.

Note: If the robot runs out of battery during cleaning, it will automatically return to the charging

base. Once the battery is fully charged, the robot can start a new cleaning cycle.

Warning: If there is no good access to the charging base, the robot will not be able to return to

its charging position. In that case, once the robot has stopped, take it manually to the charging

base.

05471_Conga 1790 Vital_IM_YV_01200611.indd 40-4105471_Conga 1790 Vital_IM_YV_01200611.indd 40-41 12/6/20 14:3312/6/20 14:33

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cecotec Conga 1790 vital Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info