753604
17
Zoom out
Zoom in
Vorherige Seite
1/85
Nächste Seite
3332
ENGLISH ENGLISH
7. Charging terminals
8. Battery
9. Side brush
10. Bumper
11. Motor cover
12. Main brush: for cleaning all types of surfaces
13. Left side wheel
14. Right side wheel
15. Silicone brush: special for pet hair
16. Cepillo Jalisco (brush): specific for hard floors
17. Optical sensor: specific for preventing the robot from bumping
Fig. 3
Wet & dry tank
Water compartment
1. Tank lock
2. Water inlet
3. Water tank
Fig. 4
Dust compartment
1. High-efficiency filter
2. Dust compartment
Fig. 5
Dust tank
1. Dust tank
2. Primary filter
3. High-efficiency filter
4. Dust tank cover
Fig. 6
Charging base
1. Signal transmission area
2. Charging terminals
3. Charge indicator
4. Cable slot
5. Charging terminals
Fig. 7
Mop bracket and cloth
1. Mop cloth
2. Mop bracket
3. Velcro
4. Tab
3. BEFORE US
Take the product out of the box and remove all packaging material.
Make sure all parts and components are included and in good conditions. If any visible signs of
damage are observed, contact the Technical Support Service immediately.
4. INSTALLATION
Fig. 8
Robot and charging base installation
Connect the charging base to a power supply and store the remaining cable. It is important to
store the remaining cable at the bottom of the charging base to avoid it from being dragged
and disconnected.
Fig. 9
Place the charging base against the wall, leaving the safety distance indicated in the picture
below.
Warning: Do not expose the charging base to direct sun light.
Long press the on/off button for 3 seconds; when the light indicator turns on, place the robot
on the charging base.
Steady blue light: On/operating
Orange light blinks: charging
Red light blinks: error
Fig. 10
Note:
Take the robot to the charging base if the battery is low. The robot might not turn on if the
battery is very low.
The robot will automatically turn on when placed on the charging base.
The robot cannot be turned off during charging.
Wet & dry tank installation
Note: It is not suggested to use the scrubbing function for the first-time use.
Open the tank’s rubber lid, fill the tank with water carefully so water does not come out and
close it again. Make sure the silicone clip is properly closed to avoid water from spilling.
Fig. 11
Install the tank in the robot following the indicated direction. Make sure the clip is properly
17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Cecotec Conga 5090 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info