Bedienungsanleitung Celestron 22403- Inspire 100AZ (Seite 5 von 40) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

666991

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

ENGLISH | 5

ALIGNING THE STARPOINTER PRO FINDERSCOPE

The StarPointer Pro ﬁ nderscope helps you aim your telescope by looking through its round glass window and covering your target with the

red reticle projected in the window. The ﬁ rst time you assemble your telescope, you will need to align the ﬁ nderscope with the main optics

of the telescope. Although this step can be done at night, it is signiﬁ cantly easier during the day. Once you have completed the ﬁ nderscope

alignment, you should not have to repeat this step unless the ﬁ nderscope is bumped or the telescope is dropped.

1. Take the telescope outside during the day. Using your naked eye, ﬁ nd an easily recognizable object, such as a streetlight, car license plate,

or tall tree. The object should be as far away as possible, but at least a quarter mile away.

2. Remove the main dust cover from the telescope and make sure your 20 mm eyepiece is installed.

3. Move the telescope left and right or up and down so that it is roughly pointing toward the object you chose in step 1.

4. Look through the telescope’s eyepiece and manually move the telescope until the object you chose lies in the center of the view. If the

image is blurry, gently turn the focus knobs until it comes into sharp focus.

5. Once the object is centered in your 20 mm eyepiece, turn on the ﬁ nderscope by turning the on/off/brightness switch knob on the bottom

of the unit as far as it will go.

6. With your head positioned about a foot behind the ﬁ nder, look through the round window and locate the red reticle. It will probably be

close to, but not on top of, the object you see when you are looking through the 20 mm eyepiece.

7. Without moving the telescope, use the two adjustment knobs on the side and underneath the ﬁ nderscope. One controls the left-right

motion of the reticle, while the other controls the up-down motion. Adjust both until the reticle appears over the same object you are

observing in the 20 mm eyepiece.

Now choose some other distant targets to practice aiming your telescope. Look through the StarPointer Pro ﬁ nderscope window and place

the red reticle over the target you are trying to view and verify that it appears in the eyepiece of the scope.

With your ﬁ nderscope aligned, your telescope is fully assembled and you are ready to observe!

NOTE: Be sure to turn off the StarPointer Pro ﬁ nderscope when not in use to conserve battery power.

YOUR FIRST ASTRONOMICAL OBSERVING SESSION

THE MOON

Now you are ready to take your telescope out at night and do some real observing!

Let’s start with the Moon. The Moon takes about one month go through a complete phase cycle, from new Moon to full Moon and back

again. Try observing it at different points during this cycle.

While you can observe the Moon any time it is visible in the sky, the best time to view it is from two days after a New Moon up to a few days

before a Full Moon. During this period, you will be able to see the most detail in craters and lunar mountain ranges. Consult a calendar or

moon phase app to ﬁ nd out when the next new Moon will be.

MOVING THE TELESCOPE

The Inspire altazimuth mount is simple to use. To move the scope

left and right, loosen the azimuth tension knob at the base of the

mount between two of the tripod legs. Grab the knob at the end

of the panning handle and move the scope to the desired location.

You can adjust the tension of the left and right motion by adjusting

the azimuth tension knob.

To move the scope up and down, loosen the altitude clutch by turning

the knob at the end of the panning handle counter-clockwise. Move the

handle up or down as required and turn the knob clockwise to lock

the scope on target.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Celestron 22403- Inspire 100AZ Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info