Bedienungsanleitung Celestron 47003 (Seite 3 von 15) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

791748

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

y Temperature Alert – hold the “ALERT” button down for a couple of seconds to enter the setup

mode and temperature digits will flash. Press “+” or “-” button to select the indoor temperature

or outdoor sensor temperature and then press “ALERT” to confirm the setting. Press the “=” or

“-” button to set the upper and lower limits (icons will flash) of the temperature and then press

“ALERT” to confirm each setting. Press the “ALERT” button to turn the alert function on or off

(you will see the icons or not).

y Alarm Setting – Press “MODE” button twice to enter the setting mode and then press and hold

down for the “MODE” button to set the alarm time. Enter the desired hour and minute values by

pressing the “+” and “-“button and pressing “MODE” to set each. Press “MODE” button twice

to show the alarm time and the “ALM.” icon will be displayed briefly. Press the “ALARM

ON/OFF” button to have an icon appear (above the seconds display) meaning that the alarm is

enabled. To turn the alarm off (disable) press “ALARM ON/OFF” button again and the alarm

icon will disappear.

y Snooze – when the alarm goes off, press the “SNOOZE” button to go into snooze mode and the

alarm will go off again after 5 minutes. To stop the snooze, press any button.

y Channel – if your Sensor is set correctly to Channel 1, then a small icon to the left of outdoor

temperature display will show a “1” in a box. If you do not have an outdoor temperature and

humidity display, make sure that the “1” is displayed and if not (shows a 2 or 3), then push the

“CHANNEL” button until it shows the “1”.

y Placement – the Receiver can be put on a table, desk, or other flat surface or it can (by using a

hanger cut out on the rear of the Receiver) be hung on a wall or other location. If hanging on a

flat surface, remove the base prior to hanging.

y Reset – if for some reason the LCD display does not function properly and you are using new

batteries, use a pin (or other very small object) to press the “RESET” button on the rear of the

Receiver.

Specifications:

y Indoor Temperature Range = 0º to +50º C (+ 32º to + 122º F)

y Remote Sensor Temperature Range = -50º to + 70º C ( -58º to + 158º F)

y Indoor Humidity Range = 30% to 90% Relative Humidity

y Resolution = ± .5º C (± 1.5º F) for temperature & ± 1.5% humidity

y Clock = digital quartz

y Transmission = RF433 MHz

y Dimensions = Receiver – 3.8” x 2.5” x 6.7” (97mmx64mmx170mm) Sensor - 2.5” x 1.2” x 3.6”

(63mmx30mmx91mm)

y Weight = Receiver - 8oz ( 227g) Sensor - 5oz (142g)

2835 Columbia St.

Torrance, California 90503 U.S.A.

www.celestron.com

Printed in China 0110 RoHS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Celestron 47003 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info