Bedienungsanleitung Celestron 47009 (Seite 3 von 30) (Englisch)

482685

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

Calibrating & Installing the Batteries of the Anemometer

After mounting the Anemometer, you need to calibrate the wind direction so that the Anemometer

properly measures the wind direction and transmits this information to the Receiver. Be sure the

batteries have been removed from the Anemometer before the calibration. You will have to

recalibrate the Anemometer whenever you replace the batteries.

Use the compass on the Anemometer and turn the wind vane so it is pointing due north (see drawing).

Hold the wind vane pointing due north and install the batteries. The red LED above the battery door

will flash a few times right after battery installation. Be sure the vane is pointing due north at the

moment when the red LED flashes and then the calibration is completed. Replace the battery door.

Press and hold the “CHANNEL/SEARCH” button a few seconds and the Channel 1 readings will

appear within 10 minutes if the wireless sensor transmission is successful.

Set Up the Power and Installation of the Rain Gauge

Choose a mounting location for the Rain Gauge that is a flat and level surface 164ft (50m) or closer in

an open area from the Receiver where data can be transmitted easily. The Rain Gauge should not be

blocked on the top or sides so that rain can freely reach the gauge (do not put under an overhang or

too close to a building or fence). Also, do not mount too close to the ground or to trees or plants.

To install the batteries in the Rain Gauge, turn it upside down (image below). Then, at the same time

push the two clips (inside of the two large holes at the ends) inward and lift off the cover and battery

compartment. Now turn the removed part upside down (image to the right) and pull out on the two

clips of the battery cover. Insert two AA batteries (user supplied) per the polarity markings on the

battery compartment. Then, replace the battery cover. Finally, replace the battery compartment and

cover into the outer housing by aligning with the clips and then pushing down on the cover over the

clips until they are secure.

Push and hold the “CHANNEL/SEARCH” button for a few seconds and the total rainfall will flash.

The total rainfall reading should appear within two minutes. If no display for total rainfall after two

minutes, then move the Rain Gauge closer and remove the batteries and repeat the above steps again.

Once the transmission to the Receiver is ok, then you are ready to

mount the Rain Gauge. Hold the base of the Rain Gauge flat

against the mounting surface and then use a level to make sure the

Rain Gauge is horizontally level. Use a pencil to trace the inside

of the mounting holes on the base of the Rain Gauge to mark the

screw locations. Drill a hole in the center of each marked screw

location and insert the supplied plastic screw plugs. Hold the Rain

Gauge against the mounting surface so the holes on the base are aligned with the plastic screw plugs

and then thread the supplied screws into each hole and use a screwdriver to tighten them.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Celestron 47009 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info