Bedienungsanleitung Celestron AstroMaster 130 EQ-MD (Seite 29 von 32) (Englisch)

580485

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Figure 7-3

A collimated telescope

should appear as a

symmetrical ring pattern

similar to the diffraction

disk seen here.

It is best to use the optional collimation tool or collimating eyepiece. Look into the focuser and notice if

the secondary reflection has moved closer to the center of the primary mirror.

With Polaris or a bright star centered within the field of view, focus with either the standard ocular or your

highest power ocular, i.e. the shortest focal length in mm, such as a 6mm or 4mm. Another option is to use

a longer focal length ocular with a Barlow lens. When a star is in focus it should look like a sharp pinpoint

of light. If, when focusing on the star, it is irregular in shape or appears to have a flare of light at its edge,

this means your mirrors aren’t in alignment. If you notice the appearance of a flare of light from the star

that remains stable in location, just as you go in and out of exact focus, then re-collimation will help

sharpen the image.

When satisfied with the collimation, tighten the small locking screws.

Take note of the direction the light appears to flare. For example, if it appears to flare toward the three

o'clock position in the field of view, then you must move whichever screw or combination of collimation

screws necessary to move the star’s image toward the direction of the flaring. In this example, you would

want to move the image of the star in your eyepiece, by adjusting the collimation screws, toward the three

o'clock position in the field of view. It may only be necessary to adjust a screw enough to move the star’s

image from the center of the field of view to about halfway, or less, toward the field's edge (when using a

high power ocular).

Collimation adjustments are best made while viewing the star's position in

the field of view and turning the adjustment screws simultaneously. This

way, you can see exactly which way the movement occurs. It may be

helpful to have two people working together: one viewing and instructing

which screws to turn and by how much, and the other performing the

adjustments.

IMPORTANT: After making the first, or each adjustment, it is necessary

to re-aim the telescope tube to re-center the star again in the center of the

field of view. The star image can then be judged for symmetry by going

just inside and outside of exact focus and noting the star's pattern.

Improvement should be seen if the proper adjustments are made. Since

three screws are present, it may be necessary to move at least two to achieve

the necessary mirror movement.

Figure 7-2

Even though the star pattern appears the same on both sides of focus, they are asymmetric. The dark

obstruction is skewed off to the left side of the diffraction pattern indicating poor collimation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Celestron AstroMaster 130 EQ-MD Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Celestron AstroMaster 130 EQ-MD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info