Bedienungsanleitung Celestron CGE Pro 1400 (Seite 46 von 72) (Englisch)

667042

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Because of the high magnifications during eyepiece projection, the field of view is quite small which makes it difficult to find

and center objects. To make the job a little easier, align the finder as accurately as possible. This allows you to get the object

in the telescope's field based on the finder's view alone.

Another problem introduced by the high magnification is vibration. Simply tripping the shutter

 even with a cable release

 produces enough vibration to smear the image. To get around this, use the camera's self-timer if the exposure time is less

than one second

 a common occurrence when photographing the Moon. For exposures over one second, use the "hat trick."

This technique incorporates a hand-held black card placed over the aperture of the telescope to act as a shutter. The card

prevents light from entering the telescope while the shutter is released. Once the shutter has been released and the vibration

has diminished (a few seconds), move the black card out of the way to expose the film. After the exposure is complete, place

the card over the front of the telescope and close the shutter. Advance the film and you're ready for your next shot. Keep in

mind that the card should be held a few inches in front of the telescope, and not touching it. It is easier if you use two people

for this process; one to release the camera shutter and one to hold the card. Here's the process for making the exposure.

1. Find and center the desired target in the viewfinder of your camera.

2. Turn the focus knob until the image is as sharp as possible.

3. Place the black card over the front of the telescope.

4. Release the shutter using a cable release.

5. Wait for the vibration caused by releasing the shutter to diminish. Also, wait for a moment of good seeing.

6. Remove the black card from in front of the telescope for the duration of the exposure (see accompanying table).

7. Replace the black card over the front of the telescope.

8. Close the camera's shutter.

Advance the film and you are ready for your next exposure. Don't forget to take photos of varying duration and keep accurate

records of what you have done. Record the date, telescope, exposure duration, eyepiece, f/ratio, film, and some comments on

the seeing conditions.

The following table lists exposures for eyepiece projection with a 10mm eyepiece. All exposure times are listed in seconds or

fractions of a second.

Planet ISO 50 ISO 100 ISO 200 ISO 400

Moon

4 2 1 1/2

Mercury

16 8 4 2

Venus

1/2 1/4 1/8 1/15

Mars

16 8 4 2

Jupiter

8 4 2 1

Saturn

16 8 4 2

The exposure times listed here should be used as a starting point. Always make exposures that are longer and shorter than the

recommended time. Also, take a few photos at each shutter speed. This will ensure that you get a good photo. It is not

uncommon to go through an entire roll of 36 exposures and have only one good shot.

NOTE: Don't expect to record more detail than you can see visually in the eyepiece at the time you are photographing.

Table 7-2

Recommended exposure time for pho

tographing planets.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Celestron CGE Pro 1400 Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info