667034
11
Zoom out
Zoom in
Vorherige Seite
1/140
Nächste Seite
ENGLISH | 11
Adjusting the Mount for Very High or
Low Latitudes
The EQ head can be set on the tripod in three different positions to
optimize the center of balance over the tripod, or to provide more
clearance when needed at lower latitudes. Additionally, the EQ head can
be positioned so that the counterweight shaft is directly above a tripod
leg (recommended default), or rotated so that the counterweight shaft is
between two of the tripod legs for additional low latitude clearance.
1. Remove the head from the baseplate by removing the 4 socket-
head screws.
2. Carefully remove the 8 socket head screws located under the head.
Once they are removed, the altitude adjustment mechanism will be the
only thing securing the bottom plate of the EQ head (Figure 10.1).
3. Turn the altitude adjuster knob until the threaded holes on the bottom
of the mount align with the new set of holes on the bottom plate. Shift
the plate forward (towards the counterweight shaft side) if you wish to
use at lower latitudes. Shift the plate backward (towards the altitude
adjustment knob) if you wish to use at higher latitudes (Figure 10.2).
USB Port on the Mount
The USB port on the CGX-L is used to interface with your PC for
use with the dedicated telescope control software. Simply connect a
standard USB B type cable into the USB port on the mount, and plug
into your PC. The mount should automatically install and assign a COM
port to your devices.
The USB port on the mount is not intended to be used with ASCOM or
third party telescope control software. To control the mount via ASCOM,
connect your PC to the NexStar+ hand control’s mini USB port.
Mini USB Port on the NexStar+ Hand Control
The mini USB port on the hand control can be used to connect to your
PC for these purposes:
1. To update the hand control and motor control board firmware.
2. To interface with third-party software that uses ASCOM.
Aux Ports
Aux 1 and Aux 2 can be used for the NexStar+ hand control, as well as
optional accessories such as the StarSense AutoAlign and SkyPortal
WiFi module.
The CGX-L is equipped with two additional Aux ports located under the
dovetail saddle. You can use any of the same accessories in these Aux
ports. They move with the declination axis of the mount, and depending
on your cable configuration, it can be a convenient location to plug in
your accessories.
Autoguide Ports
The autoguide port should only be used for autoguide camera relays.
CAUTION: Never plug the NexStar+ hand control or other accessory
into the autoguide port. Damage could result.
The CGX-L is equipped with a redundant autoguider port, located next
to Aux 3 and Aux 4 near the dovetail saddle. You can only use one
autoguide port. The redundant port is intended to provide you with the
best option that suits your particular cable configuration.
Figure 10.2 Changing the mount position on the tripod head
DEFAULT POSITION
BACK POSITION
FRONT POSITION
Figure 10.1
Socket Head Screws
Securing Baseplate
Baseplate
11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Celestron CGX-L EQUATORIAL wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info