Bedienungsanleitung Celestron CPC Deluxe 1100 HD - 11009 (Seite 9 von 50) (Englisch)

667032

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

>> www.celestron.com

Aligning the Finderscope

The nderscope is adjusted using two adjustment screws, located on

the top and on the right (when looking though the nder) of the nder

bracket and a spring loaded pivot screw (located on the left side of the

bracket). This allows you to turn the top adjustment screw to move the

nderscope up and down, and turn the right adjustment screw to move

the nderscope right to left. The spring loaded pivot screw puts constant

pressure on the nder so that the adjustment screws are always making

contact with the nder.

To make the alignment process a little easier, you should perform this

task in the daytime when it is easier to locate objects in the telescope

without the nder. To align the nder:

1. Choose a conspicuous object that is in excess of one mile away. This

will eliminate any possible parallax eect between the telescope and

the nder.

2. Point your telescope at the object you selected and center it in the

main optics of the telescope.

3. Lock the azimuth and altitude clamps to hold the telescope in place.

4. Check the nder to see where the object is located in the eld of view.

5. Adjust the thumb screws on the nder bracket until the cross hairs are

centered on the target.

Remember that the image orientation through the nder is inverted

(i.e., upside down and reversed from left-to-right). Because of this, it may

take a few minutes to familiarize yourself with the directional change

each screw has on the nder.

Attaching the Hand Control

In order to protect your CPC telescope during shipping, the hand control

unit has been packaged along with the other telescope accessories and

will need to be plugged in to the drive base of your telescope. The hand

control cable has a phone jack style connector that will plug into the

designated jack outlet located on the top of the drive base (see gure

3-10). Your telescope also comes with a hand control holder that must be

attached to the fork arm. To connect the hand control to the fork arm:



• Locate the hand control holder and slide it down into the slot located

on the fork arm (see gure 3-9).

• Push the connector into the jack until it clicks into place.

The hand control can now rest in the holder on the fork arm

of the telescope.

Powering the CPC

The CPC can be powered by the supplied 12v car battery adapter or

optional power supply (see Optional Accessories section in the back

of this manual).

1. To power the CPC with the car battery adapter, simply plug the round

post into the designated 12v power outlet located on the drive base.

2. Turn on the power to the CPC by ipping the On/O switch.









Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Celestron CPC Deluxe 1100 HD - 11009 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info