Bedienungsanleitung Celestron LCM Series (Seite 6 von 35) (Englisch)

580474

Zoom out

Zoom in

Vorherige Seite

1/35

Nächste Seite

assembly

The LCM comes partially assembled and can be operational

in a matter of minutes. The LCM is conveniently packaged

in one reusable shipping carton that contains the following

accessories:

• 25mmand9mmEyepieces

• ErectImageDiagonal(60/70/80/90LCMonly)

• StarPointerFinderscope

• AccessoryTray

• The SkyX Student Edition Astronomy Software

• LCMHandControlw/4,000ObjectDatabase

aSSeMbLing The TeLeSCope

Your LCM comes in three major sections: the optical tube,

the motorized mount and the tripod. These sections can be

attached in seconds using the quick release coupling screw

located under the tripod mounting platform and the dovetail

mounting clamp located on the outside of the motorized base.

To begin, remove all of the accessories from their individual

boxes. Remember to save all of the containers so that they can

be used to transport the telescope. Before attaching the visual

accessories, the telescope tube and mount should be attached

to the tripod. First, install the accessory tray onto the

tripod legs:

1. Remove the tripod from the box and spread the legs apart

until the center leg brace is fully extended.

2. Locate the accessory tray, and place it on top of the tripod

center support brace in between the tripod legs

(seegure2-1).

3. Rotate the accessory tray so that the central hole in the

tray slides over the ﬂange post in the center of the

support bracket.

4. Finally, rotate the tray so that the locking tabs slide under the

locking clips on center leg brace. You will feel the tray snap

into place.

It is a good idea to level the tripod by adjusting the height of

the tripod legs before attaching the motorized base and tube.

Minor adjustments can be made later. To adjust the height of

the tripod legs:

1. Lift the tripod leg locking lever located on the side of

each leg.

2. Slide the inner portion of each leg down 6” to 8” inches.

3. Adjust the tripod height until the base is visually level and

press down the locking levers to secure into place.

Attaching the Hand Control Holder

The LCM comes with a snap-on hand control holder that

conveniently attaches to any of the tripod legs. To attach the hand

control holder simply position the holder with the square plastic

tab facing up and push against the tripod leg until it snaps in

to place.

Attaching the Motorized Base to the Tripod

With the tripod properly assembled, the motorized base can

easily be attached using the quick release coupling screw

located underneath the tripod mounting platform:

1. Place the motorized base on top of the tripod making sure

that the three round feet rest on the round ﬂat pads on the

inside of the tripod head.

2. Thread the coupling screw into the hole at the bottom of the

motorized base and hand tighten.

Figure 2-1

Flange Post

Locking Tabs

Locking

Clips

Figure 2-4

Motorized

Base

Tripod

Mounting

Platform

Coupling

Screw

Figure 2-3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Celestron LCM Series Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Celestron LCM Series

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info