Bedienungsanleitung Celestron NexStar 5SE (Seite 6 von 54) (Englisch)

580478

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

The NexStar 5 comes completely pre-assembled and can be operational in a matter of minutes. The NexStar is conveniently

packaged in one reusable shipping carton that contains all of the following accessories:

• 25mm Eyepiece – 1

¼"

• Star Diagonal 1¼"

• Star Pointer Finderscope

• Steel Tripod with built-in Wedge

• The Sky™ Level 1 Astronomy Software

• NexRemote telescope control software

• RS232 Cable

• Camera Shutter Cable

• Computerized Hand Control with nearly 40,000 Object Database

Start by removing the telescope from its shipping carton and setting the round base on a flat table or surface. It is best to carry the

telescope by holding it from the lower portion of the fork arm and from the bottom of the base. Remove all of the accessories

from their individual boxes. Remember to save all of the containers so that they can be used to transport the telescope. Before

the batteries can be installed, the telescope tube should be positioned horizontal to the ground. To do this, gently rotate the front

of the tube upwards until it is level with the ground.

Powering the NexStar

The NexStar can be powered by eight AA batteries (not included), an optional 12v AC adapter or an optional car battery

adapter. The battery compartment is located in the center of the telescope's base (see figure 3-1).

To power the NexStar with batteries:

1. Remove the battery cover from the center of the base by gently lifting up on the

round portion of the cover.

2. Insert the batteries into the battery compartment of the base.

3. Reattach the battery compartment door by gently pushing down on the cover

until it snaps into place.

4. Turn on the power to the NexStar by flipping the switch, located at the base of

the fork arm, to the "On" position.

The Hand Control

The hand control is located on the side of the fork arm and can be removed and used

remotely or used while attached to the fork. The hand control attaches to the fork

arm by resting on two posts, located on the bottom of the hand control cradle, and a

clip inside the fork arm. To remove the hand control from the fork arm cradle,

gently lift the hand control upwards and pull out. To return the hand control into the fork arm, lower the hand control into the

cradle so that the two holes in the bottom of the hand control go over the posts on the bottom of the cradle, and the opening in the

back of the hand control slides over the clip inside the fork arm.

Battery Compartment

Cover

Figure 3-1: The NexStar 4/5 Battery Compartment

Once the telescope is powered up, the hand control can be used to move the optical tube in altitude (up and down) and azimuth

(side to side). Use the Up arrow directional button to move the telescope tube until it is roughly parallel to the ground. This will

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Celestron NexStar 5SE Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info