667019
6
Zoom out
Zoom in
Vorherige Seite
1/47
Nächste Seite
6
The NexStar comes partially assembled and can be operational in a matter of minutes. The NexStar is
conveniently packaged in one reusable shipping carton that contains the following accessories:
25mm and 9mm Eyepieces – 1¼"
1¼" Star Diagonal
Star Pointer Finderscope and Mounting Bracket
Deluxe Accessory Tray
The Sky™ X Astronomy Software
NSOL Telescope Control Software
NexStar Hand Control w/ Object Database
A
A
s
s
s
s
e
e
m
m
b
b
l
l
i
i
n
n
g
g
t
t
h
h
e
e
N
N
e
e
x
x
S
S
t
t
a
a
r
r
Your NexStar comes in three major sections: the optical tube, the fork arm and the tripod. These sections can
be attached in seconds using the quick release coupling screw located under the tripod mounting platform and
the dovetail mounting clamp located on the inside of the fork arm. To begin, remove all of the accessories from
their individual boxes. Remember to save all of the containers so that they can be used to transport the
telescope. Before attaching the visual accessories, the telescope tube should be mounted to its tripod. First,
install the accessory tray onto the tripod legs:
1. Remove the tripod from the box and spread the legs
apart until the center leg brace is fully extended.
2. Locate the accessory tray, and place it on top of the
tripod center support brace in between the tripod legs
(see figure 2-1).
3. Rotate the accessory tray so that the central hole in the
tray slides over the flange post in the center of the
support bracket.
4. Finally, rotate the tray so that the locking tabs slide
under the locking clips on support bracket. You will
here the tray snap into place.
It is a good idea to level the tripod and adjust the height of the tripod legs before attaching the fork arm and
tube. Minor adjustments can be made later. To adjust the height of the tripod legs:
1. Loosen the tripod leg locking bolt located on the side of each leg.
2. Slide the inner portion of each leg down 6" to 8" inches.
3. Adjust the tripod height until the bubble level on the tripod leg is
centered.
4. Tighten the tripod locking bolts to hold each leg in place.
Figure 2-1
Flange Post
Locking Tabs
Locking
Clips
Bubble
Level
Figure 2-2
6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Celestron NexStar SLT wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info