Bedienungsanleitung Celestron Omni XLT AZ - 22151 (Seite 6 von 40) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

667005

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

6 | ENGLISH

MOVING THE TELESCOPE

The Omni AZ mount has slip clutches in both axes. To make large movements with the telescope, simply hold the optical

tube and push it in the desired direction. To make ﬁne adjustments or to track celestial objects, turn both slow motion

knobs.

ALIGNING THE STARPOINTER PRO FINDERSCOPE

The Starpointer Pro Finderscope helps you aim your telescope by looking through its round glass window and covering

your target with the red recticle projected in the window.

The ﬁrst time you assemble your telescope, you’ll need to align the ﬁnderscope with the main optics of the telescope.

Although this step can be done at night, it is signiﬁcantly easier during the day. Once you have completed the ﬁnderscope

alignment, you should not have to repeat this step unless the ﬁnderscope is bumped or dropped.

1. Take the telescope outside during the day. Using your naked eye, ﬁnd an easily recognizable object, such as a streetlight,

car license plate, or tall tree. The object should be as far away as possible, but at least a quarter mile away.

2. Remove the main dust cover from the telescope and make sure your 25 mm eyepiece is installed.

3. Move the telescope left and right or up and down so that it is roughly pointing toward the object you chose in step 1.

4. Look through the telescope’s eyepiece and manually move the telescope until the object you chose lies in the center of

the view. If the image is blurry, gently turn the focus knobs until it comes into sharp focus.

NOTE: The image in the telescope eyepiece will appear upside-down. This is perfectly normal in an astronomical telescope.

5. Once the object is centered in your 25 mm eyepiece, turn on the ﬁnderscope by turning the power/brightness switch

knob on the bottom of the unit as far as it will go.

6. With your head positioned about a foot behind the ﬁnder, look through the round window and locate the red reticle. It will

probably be close to, but not on top of, the object you see when you are looking through the 25 mm eyepiece.

7. Without moving the telescope, use the two adjustment knobs on the side and underneath the ﬁnderscope. One controls

the left-right motion of the reticle, while the other controls the up-down motion. Adjust both until the reticle appears over

the same object you are observing in the 25 mm eyepiece.

Now choose some other distant targets to practice aiming your telescope. Look through the Starpointer Pro Finderscope

window and place the red dot on the target you are trying to view and verify that it is the 25 mm eyepiece of the scope.

With your ﬁnderscope aligned, your telescope is fully assembled and you are ready to observe!

NOTE: Be sure to turn off the Starpointer Pro Finderscope when not in use to conserve battery power.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Celestron Omni XLT AZ - 22151 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info