Bedienungsanleitung Celestron Rowe-Ackermann Schmidt Astrograph

666998

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Installing a Camera

Use one of the two supplied camera adapters to attach to your DSLR or CCD camera. The

M42 adapter ﬁts most cameras with standard T-threads. The wider M48 adapter can be

used with full frame cameras with minimal vignetting. DSLR cameras require a T-ring, sold

separately, for the make and model of your camera.

CCD cameras have a wide range of backfocus, depending on the model and accessories

used. The included camera adapters allow 55 mm of distance from the adapter to the

imaging sensor. If your CCD camera consumes less than 55 mm, you will need to add a

spacer to reach the correct distance.

Cameras with sensors larger than 43 mm diagonal (full frame) will require a custom adapter

to better illuminate the sensor. Refer to Celestron’s website for a drawing of our camera adapter

dimensions to help determine how a custom adapter should be made.

Note: Due to the steep light cone at f/2.2, camera housings can be a source of vignett-

ing. Despite having a large illuminated ﬁeld (78% 21 mm off-axis), vignetting can occur

when using custom adapters and when a steep housing surrounds the sensor. This is

common with DSLR sensors, sometimes resulting in rectangular vignetting.

To attach your camera:

1. Place the knurled retaining ring over the camera adapter and loosely thread it onto

the telescope.

2. Holding your camera, thread the camera body (or T-ring, if a DSLR is used) to the

camera adapter.

3. Carefully hold the camera so the camera adapter seats ﬂatly.

4. Finish threading the retaining ring onto the telescope. Turn until the camera adapter is

snug against the telescope. Do not over tighten! Camera orientation can be adjusted later.

Caution: Over tightening the camera adapter can increase the chance of loosening

the lens assembly on the corrector, or cause the lens assembly to rotate against the

corrector. Keep the camera adapter snug against the telescope, but do not over tighten.

Adjusting Camera Orientation

Once the camera is installed, you can rotate it by slightly loosening the retaining ring. Loosen

the ring no more than 1/8

turn, rotate the camera as desired, and retighten the ring,

remembering not to over tighten.

Fan Operation and Optics Cool Down

It takes time for the optics of the Astrograph to reach thermal equilibrium with the

outside air. The greater the temperature difference between where the Astrograph is

stored and the outdoors, the longer it takes to cool down.

The Astrograph is equipped with a cooling system containing a 12-volt fan. The battery

pack requires 8 AA battaries (not included). Install the battaries as indicated in the

plastic mold of the battery holder. Plug in the supplied battery pack to power the fan

before using the Astrograph. You can do this while preparing your camera equipment.

Focusing

The Feather Touch Micro Focuser knob moves the primary mirror on the rear cell of the

telescope. The larger black knob is the coarse focus; the smaller orange knob is the 10:1

ﬁne focus. Turn the focusing knob until the image is sharp on your camera. If the knob

will not turn, it has reached the end of its travel on the focusing mechanism. A single turn

of the focusing knob moves the primary mirror only slightly. Therefore, it will take many

turns (about 30) to go from close focus to inﬁnity.

If you turn the focus knob too quickly, you can go right through focus without seeing

the image. To avoid this problem, your ﬁrst astronomical target should be a bright object

(like the Moon or a planet) so that the image is visible even when out of focus. Critical

focusing is best accomplished when the focusing knob is turned counterclockwise so that

the mirror moves against the pull of gravity. This minimizes mirror shift.

Mirror Support Clutches

The Astrograph is equipped with mirror tension clutches to help support and minimize

movement of the primary mirror during long exposures.

To use the mirror clutches:

1. Use the focus knob to adjust the primary mirror to the desired focus.

2. Once in focus, turn the two mirror lock knobs clockwise until both are very tight and

can be turned no further.

Warning! Once the mirror is locked down, do not turn the focuser knob without loos-

ening the mirror locks ﬁrst. Although turning the focus knob should not damage the

telescope, undue stress can be placed on the focus mechanisms causing excessive image

shift while focusing.

Collimation

The telescope is factory aligned, but may need a slight adjustment after it is transported.

The primary mirror and corrector are permanently aligned at the factory. You can make

adjustments to the tilt of the lens assembly if needed.

The Astrograph must be collimated with the camera installed. We recommend using a

camera that does not obstruct the light path of the telescope, making it easier to see

concentric star patterns.

Equipment needed:

2 mm Hex key

3 mm Hex key

Artiﬁcial star or a star outside at night, such as Polaris

Camera setup, ready to image

1. Install the camera on the telescope as described in the “Installing a Camera” section

of this manual.

2. Rotate the camera adapter so that the 3 slotted openings allow access to the

collimation screws

3. Point the Astrograph at your star and focus the camera.

4. Defocus the star about 1 turn, using the coarse focus knob on the Feather

Touch Microfocuser.

5. Inspect the star pattern. When collimated, the pattern should look like a concentric

doughnut. If the pattern is concentric, no adjustment is necessary.

6. Adjust the telescope collimation if needed by slightly loosening a 3mm socket head

screw, and tightening the paired 2mm socket head screw. The screws work as push/pull,

tightening one requires loosening the other. Always adjust one pair of screws at a time.

7. If the star pattern is thin on one side, adjust the collimation so that the star moves

towards the thin side, then adjust the position of the Astrograph to re-center the star.

Repeat this until you achieve correct collimation.

Removing the Optical Window

The optical window can be removed and replaced with a ﬁlter, such as a light pollution

ﬁlter to improve contrast.

1. With the camera adapter removed, carefully grab hold of the knurled cell of the

optical window.

2. Carefully unthread the optical window from the Astrograph.

Attaching Accessories

The Astrograph includes a CGE-style dovetail which is also cross compatible with

most accessories that work on the Losmandy D plate. The accessory dovetail can be

used to mount an optional guidescope. The Celestron 80 mm Guide Scope package is

compatible with the accessory dovetail.

A Celestron 50 mm ﬁnder scope can also be attached using the threaded holes on the

rear cell of the telescope.

1 Front Lens Group 6 Mirror Lock Knobs

2 Corrector 7 10:1 Feather Touch Micro Focuser

3 Optical Window Cell 8 12V DC Input for Cooling Fan

4 Collimation Screws 9 Cooling Fan

5 Accessory Dovetail Plate

Overview

Knurled

retaining

ring

Collimation

screws

2 mm

Hex key

3 mm

Hex key

Knurled cell of

optical window

Parts List

Optical Tube Assembly, M42 Camera T-adapter, M48 Wide Camera Adapter, Retaining Ring, 8 x AA Battery Pack (batteries not included), Dust Cap

The Rowe-Ackermann Schmidt Astrograph delivers a ﬂat ﬁeld, coma-free image across a large image circle for your imaging camera. The Astrograph can only be used with a camera.

Celestron Rowe-Ackermann Schmidt Astrograph - 91075 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info