Bedienungsanleitung Cervelo Multi-speed racing bicycles (Seite 20 von 40) (Englisch)

658416

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Cervélo Owner’s Manual

until it comes out of the rear dropouts.

d. Installing a Quick Release Rear Wheel

(1) Make sure that the rear derailleur is still in its outermost, high

gear, position

(2) Pull the derailleur body back with your right hand.

(3) Move the quick-release lever to the OPEN position (see fig. 6).

The lever should be on the side of the wheel opposite the

derailleur and freewheel sprockets.

(4) Put the chain on top of the smallest freewheel sprocket. Then,

insert the wheel up and back into the frame dropouts and pull

it all the way in to the dropouts.

(5) Tighten the quick-release adjusting nut until it is finger tight

against the frame dropout; then swing the lever toward the front

of the bike until it is parallel to the frame’s chainstay or seatstay and

is curved toward the wheel (fig. 7). To apply enough clamping

force, you should have to wrap your fingers around a frame tube

for leverage, and the lever should leave a clear imprint in the palm of

your hand.

WARNING: Securely clamping the wheel takes considerable

force. If you can fully close the quick release without wrapping

your fingers around the seatstay or chainstay for leverage, and

the lever does not leave a clear imprint in the palm of your

hand, the tension is insufficient. Open the lever; turn the

tension adjusting nut clockwise a quarter turn; then try again.

force. If you can fully close the quick release without wrapping

your fingers around the fork blade for leverage, and the lever

does not leave a clear imprint in the palm of your hand, the

tension is insufficient. Open the lever; turn the tension adjusting

nut clockwise a quarter turn; then try again.

(5) If the lever cannot be pushed all the way to a position parallel to the

fork blade, return the lever to the OPEN position. Then turn the tension

adjusting nut counterclockwise one-quarter turn and try tightening

the lever again.

(6) Re-engage the brake quick-release mechanism to restore correct

brake pad-to-rim clearance; spin the wheel to make sure that it is

centered in the frame and clears the brake pads; then squeeze the

brake lever and make sure that the brakes are operating correctly.

c. Removing a Quick Release Rear Wheel

(1) Shift the rear derailleur to high gear (the smallest, outermost

rear sprocket).

(2) If your bike has rim brakes, disengage the

brake’s quick-release mechanism to increase

the clearance between the wheel rim

and the brake pads (see Section 4.C, fig. 8 and

9).

(3) Pull the derailleur body back with your right hand.

(4) Move the quick-release lever to the OPEN position (fig. 6).

(5) Lift the rear wheel off the ground a few inches and, with the

derailleur still pulled back, push the wheel forward and down

fig. 7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cervelo Multi-speed racing bicycles Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info