Bedienungsanleitung Cervelo S3 RIM - 2019 (Seite 62 von 196) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

780073

Zoom out

Zoom in

Vorherige Seite

1/196

Nächste Seite

Cut Line

1cm

1. Taking care to maintain the minimum required seatpost insertion of 6.5cm

and maximum of 8.5cm, carefully measure and use a light coloured grease

pencil to accurately mark the cut-o location on the seatpost.

2. Insert the S Series Seatpost in the Park Tool SG-7.2 Saw Guide (or equivalent)

so that the cut-o line can be seen clearly through the blade guide in the tool.

3. Using a blade designed specically for cutting carbon composite materials (or

a ne tooth blade with greater than 32 teeth per inch); proceed with cutting the

Seatpost (as per Park Tool’s instructions).

4. Use ne grit sandpaper to carefully remove any fraying or burring from the cut

end. Reposition clamp approximately 10cm from the cut end.

5. With a grease pencil, mark a point 1cm from the cut end on the trailing edge

of the Seatpost, and another 1cm from the back, on the bottom edge. Draw a

line connecting them, forming a 45 degree guideline.

6. Placing the blade of your saw on the grease pencil mark, very carefully

proceed to cut, resulting in a 45 degree chamfer being cut onto the trailing

edge of the Seatpost.

7. Carefully sand the end and after applying carbon assembly compound,

return to the frame.

Note: It is essential that all Cervélo Aero Seatposts, have a 45

degree chamfer cut on the rear trailing edge of the post. If trimming

is required after tting, the following method is recommended.

SEATPOST CUTTING INSTRUCTIONS

If trimming is required, ﬁnal length should allow for a

minimum 6.5 cm of seatpost remaining in the frame.

Failure to meet this requirement, may result in damage

to the frame not covered by warranty policy, or serious

injury to rider.

SEATPOST ASSEMBLY

25mm Offset Seatpost

(SP-SP20-25MM)

0mm Offset Seatpost

(SP-SP20-ZERO)

45mm

35mm

M5 Seatpost

Fixing Screws

Actual Size

1. Ensure Loctite 242 is applied to threads

below the head of the 45mm button

head cap screw. Install cross bar on

45mm button head cap screw and

torque to 3Nm.

2. Ensure Loctite 242 is applied to both

xing screw threads.

3. Install the curved washer and

adjustment dial in the seatpost cutout.

4. Install the button head cap screw with

crossbar installed, and turn the dial

until threads are engaged.

5. Install the spherical washer on the

35mm spherical cap screw, so that the

concave face, mates with the convex

surface of the screw.

6. Install cross bar.

7. Apply light coat of carbon assembly

compound to the radius on the upper

face of the seatpost.

8. Install the lower saddle clamp base, as

per the diagram.

9. Locate saddle rails between upper and

lower clamping surfaces.

10. Establish desired saddle angle by rst

using adjustment wheel.

11. Tighten opposing angle adjusting

screw to secure saddle at 8-9Nm.

Button Head

Cap Screw

M5 X 45

Button Head

Cap Screw

M5 X 45

Crossbar

Saddle Clamp

Base

Adjustment

Wheel

Adjustment

Wheel

Spherical

Cap Screw

M5 X 35

Spherical

Cap Screw

M5 X 35 NOTE: The S Series

seatpost is compatible

with both metallic

saddle rails (7mm

diameter) and carbon

saddle rails (7x9mm

cross section).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cervelo S3 RIM - 2019 Seite 62

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info