555434
40
Zoom out
Zoom in
Vorherige Seite
1/48
Nächste Seite
39
Operation
Remote Control
Your remote control has been programmed at the factory to operate with your garage door opener.
Older Chamberlain remote controls are NOT compatible, see page 44 for compatible accessories.
Programming can be done through the door control or the learn button the garage door opener. To
program additional accessoriesrefer to the instructions provided with the accessory or visit
www.chamberlain.com. Ifyour vehicle is equipped with a Homelink
®
, you may require an external
adapter depending on the make, model, and year of your vehicle.Visitwww.homelink.com for additional
information.
TO ADD, REPROGRAM, OR CHANGE A REMOTE CONTROL/KEYLESS ENTRY PIN
USING THE MOTION-DETECTING CONTROL PANEL
1. Press the LEARN button on the door control to enter Programming Mode.
2. Press the LEARN button again, the LED will flash once.
3. Remote Control:
Press the button on the remote control that you wish to operate your garage door. Keyless
Entry: Enter a 4-digitpersonal identification number (PIN) ofyour choice on the keylessentry
keypad. Then pressthe ENTER button.
The garage door opener lights will flash (or two clicks will be heard) when the code has been
programmed. Repeat the stepsfor programming additional remote controlsor keylessentrydevices.
The command LED
will flash once.
The command LED will
flash once again.
1
2
OR
PIN
? ? ? ?
4
GHI
5
JKL
7
P
RS
8
TUV
9
WXY
0
QZ
*
#
E
NT
E
R
0 QZ
*
#
ENTER
6
MNO
3
TO ADD, REPROGRAM, OR CHANGE A REMOTE CONTROL/KEYLESS ENTRY PIN
USING THE SMART CONTROL PANEL
1. Press the navigation button below "MENU" to view the Features menu.
2. Use the navigation buttons to scroll to "PROGRAM".
3. Select "REMOTE" or "KEYPAD" to program from the program menu.
4. Remote Control:
Press the button on the remote control that you wish to operate your garage door. Keyless
Entry:
Enter a 4-digit personal identification number (PIN) ofyour choice on the keyless entry keypad.
Then pressthe ENTER button.
The garage door opener lights will flash (or two clicks will be heard) when the code has been
programmed. Repeat the stepsfor programming additional remote controlsor keylessentrydevices. If
programming isunsuccessful, program the remote using the learn button.
Press to continue.
TO REMOTE
Press to continue.
1
2 3
OR
PIN
? ? ? ?
4
GHI
5
JKL
7
P
RS
8
TUV
9
WXY
0
QZ
*
#
E
NT
E
R
0 QZ
*
#
ENTER
6
MNO
4
40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Chamberlain 349544 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info