Bedienungsanleitung Chamberlain CG40D 1-2 HP (Seite 4 von 40) (Englisch)

555405

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Safety Reversing Sensor

Horizontal and vertical reinforcement

is needed for lightweight garage doors

(fiberglass, steel, aluminum,

door with glass panels, etc.).

See page 23 for details.

— — — — — — — —

Header Wall

Safety

Reversing

Sensor

Gap between floor and bottom of door

must not exceed 1/4" (6 mm).

Extension Spring

Torsion Spring

Access

Door

Slack in chain tension

is normal when

garage door is closed.

Wall-mounted

Door

Control

Motor Unit

FINISHED CEILING

Support bracket &

fastening hardware

is required.

See page 16.

Vertical

Centerline

of Garage Door

SECTIONAL DOOR INSTALLATION

Planning

Identify the type and height of your garage door. Survey

your garage area to see if any of the conditions below

apply to your installation. Additional materials may be

required. You may find it helpful to refer back to this page

and the accompanying illustrations as you proceed with

the installation of your opener.

Depending on your requirements, there are several

installation steps which may call for materials or hardware

not included in the carton.

• Installation Step 1 – Look at the wall or ceiling above

the garage door. The header bracket must be securely

fastened to structural supports.

• Installation Step 5 – Do you have a finished ceiling in

your garage? If so, a support bracket and additional

fastening hardware may be required.

• Installation Step 10 – Depending upon garage

construction, extension brackets or wood blocks may be

needed to install sensors.

• Installation Step 10 – Alternate floor mounting of the

safety reversing sensor will require hardware not

provided.

• Do you have an access door in addition to the garage

door? If not, Model 7702CB Emergency Key Release is

required. See Accessories page.

Trolley

Header

Wall

Garage

Door

Header

Bracket

Straight

Door

Arm

Emergency

Release

Rope & Handle

Door

Bracket

Curved

Door

Arm

Garage

Door

Spring

Chain

Trolley

Stop Bolt

CLOSED POSITION

• Look at the garage door where it meets the floor. Any

gap between the floor and the bottom of the door must

not exceed 1/4" (6 mm). Otherwise, the safety reversal

system may not work properly. See Adjustment Step 3.

Floor or door should be repaired.

SECTIONAL DOOR INSTALLATIONS

• Do you have a steel, aluminum, fiberglass or glass

panel door? If so, horizontal and vertical reinforcement

is required (Installation Step 11).

• The opener should be installed above the center of the

door. If there is a torsion spring or center bearing plate

in the way of the header bracket, it may be installed

within 4 feet (1.22 m) to the left or right of the door

center. See Installation Steps 1 and 11.

• If your door is more than 7 feet (2.13 m) high, see rail

extension kits listed on Accessories page.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Chamberlain CG40D 1-2 HP Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info