Bedienungsanleitung Chamberlain WD832KEV (Seite 35 von 44) (Englisch)

555436

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Operation

Motion Detecting Control Panel (continued)

LOCK

The LOCK feature is designed to prevent activation of the garage door opener from remote controls

while still allowing activation from the door control and keyless entry. This feature is useful for added

peace of mind when the home is empty (i.e.vacation).

Activate: Pressand hold the LOCK button for 2 seconds.The command LED will flash as long

as the lock feature is activated and your handheld remote control will not operate your door at

this time.

Deactivate: Press and hold the LOCK button again for 2 seconds.The command LEDwill stop

flashing and normal operation will resume.

TIMER-TO-CLOSE

DO NOT enable TTC if operating a one-piece door. The TTC can be turned on or offand the time

interval can be adjusted to 1, 5,and 10 minute intervals. Once the TTC has been setand the door is

open, the selected close interval will blink and begin to count down to close the door.

Activate: Pressand hold the ON button until one ofthe TTC LEDslight up. Then press the ON

button again to cycle through the time interval options (the corresponding TTC LEDwill light for

each time interval). The garage door opener lightbulbs will blinkasconfirmation.

Deactivate: Press and hold the OFF button until all TTC LEDsturn offand a beep is heard from

the motor unit.

Temporarily hold door open (suspend TTC): Press and release the HOLD OPEN button. Press

the HOLD OPENbutton again to resume normal TTC operation.

PROGRAM

Any compatible remote controls,wirelesskeyless entry, or MyQ

accessories can be programmed to the

garage door opener by pressing the Learn button.

ON (TTC)

OFF (TTC)

Command LED

Motion Sensor

Switch

LIGHT

Button

HOLD OPEN

Button(TTC)

Motion

Sensor

Push Bar

1, 5, and

10 Minute

TTC LED

LEARN Button

LOCK Button

Remote Control

Your remote control has been programmed at the factory to operate with your garage door opener.

Older Chamberlain remote controls are NOT compatible, see page 40 for compatible accessories.

Programming can be done through the door control or the learn button the garage door opener.To

program additional accessories refer to the instructions provided with the accessory or visit

www.chamberlain.com.Ifyour vehicle is equipped with a Homelink

, you may require an external

adapter depending on the make,model,and year ofyour vehicle. Visit www.homelink.com for additional

information.

TO ADD, REPROGRAM, OR CHANGE A REMOTE CONTROL/KEYLESS ENTRY PIN

USING THE MOTION-DETECTING CONTROL PANEL

1. Press the LEARNbutton on the door control to enter Programming Mode.

2. Press the LEARNbutton again, the LED will flash once.

3. Remote Control:

Press the button on the remote control that you wish to operate your garage door. Keyless

Entry:

Enter a 4-digit personal identification number (PIN) of your choice on the keyless entrykeypad.

Then press the ENTER button.

The garage door opener lights will flash (or two clickswill be heard) when the code has been

programmed. Repeat the stepsfor programming additional remote controls or keyless entrydevices.

The command LED

will ﬂash once.

The command LED will

ﬂash once again.

? ? ? ?

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Chamberlain WD832KEV Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info