Bedienungsanleitung Char-Broil Patio Bistro 180 (Seite 4 von 69) (Alle Sprachen)

716814

Zoom out

Zoom in

Vorherige Seite

1/69

Nächste Seite

CAUTION

SPIDER ALERT!

SPIDER AND WEBS

INSIDE BURNER

If your appliance is getting hard to light or the flame

is weak, check and clean the venturis and burners.

Spiders or small insects are known to create

“flashback” problems by building nests and laying

eggs in the appliance’s venturi or burner obstructing

the flow of gas. The backed-up gas can ignite behind

the control panel. This flashback can damage your

appliance and cause injury. To prevent flashbacks

and ensure good performance, the burner and

venturi tube assembly should be removed and

cleaned whenever the appliance has been idle for an

extended period of time.

Cleaning the Burner Assembly

Follow these instructions to clean and/or replace parts

of burner assembly or if you have trouble igniting

appliance.

1. Turn gas control knob to and remove

cartridge.

2. Open top cover, remove cooking grate and warming

rack, shown A. This will expose the burner from

inside, shown B.

3. Remove 3 screws attaching burner, shown C

4. From the top of the grill, carefully lift burner out,

shown D.

5. Clean any blocked ports with a stiff wire such as an

open paper clip.

6. Clean burner as recommended below, shown E.

We suggest three ways to clean the burner tube.

Use the one easiest for you.

(A) Bend a stiff wire (a light weight coat hanger works

well) into a small hook. Run hook through burner

tube several times.

(B) Use a narrow bottle brush with a flexible handle (do

not use a brass wire brush), run the brush through

burner tube several times.

into the burner tube and out the burner ports.

Check each port to make sure air comes out each

hole.

7. Check burner for damage, due to normal wear and

corrosion some holes may become enlarged. If any

large cracks or holes are found replace burner.

8. Insert burner into firebox .

VERY IMPORTANT: Burner tube must re-engage over

valve opening. See illustration, shown F.

9. Reattach burner with screws removed in step 3.

10. Reinstall heat tent, cooking grates and warming

rack.

Leak Testing Valves, Tube and Regulator

Ensure Cooking Grate ridges run front to back (fig.A)

Burner

(exposed)

Warming

Rack

Cooking

Grate

Burner

Screws

Move burner to rear

and upward

Tube cleaner

(see above

recommendations)

Burner

(removed)

Orifice engaged inside burner

tube end correctly

Burner

Tube

Orifice

Warming

Rack

Warming

Rack

Brush soapy solution onto connections between regulator

piping to valve (B). If a leak is detected remove cylinder. Do not

use grill with a leak and do not attempt to correct.

2. Brush soapy solution onto connection between gas cylinder

and regulator at (A). If growing bubbles appear, there is a leak.

Retighten cylinder and repeat soapy solution.

3. If you cannot stop a leak, remove gas cylinder from regulator

and check for damaged threads, dirt and debris on regulator and

gas cylinder. Also check to see if anything is obstructing flow of

gas at regulator and gas cylinder openings. Remove any

obstruction that may be found and repeat leak test. IF threads

are damaged on either regulator or gas cylinder, replace.

1. Be sure control valve is turned OFF

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Char-Broil Patio Bistro 180 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info