Bedienungsanleitung Char-Broil Performance 440 (Seite 4 von 160) (Alle Sprachen)

716800

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

CAUTION

SPIDER ALERT!

If your barbeque is getting hard to light or the flame is weak,

check and clean the venturis and burners.

Spiders or small insects are known to create “flashback”

problems by building nests and laying eggs in the barbeque’s

venturi or burner obstructing the flow of gas. The backed-up

gas can ignite behind the control panel. This flashback can

damage your barbeque and cause injury. To prevent

flashbacks and ensure good performance, the burner and

venturi tube assembly should be removed and cleaned

whenever the barbeque has been idle for an extended period

of time.

SPIDER AND WEBS

INSIDE BURNER

IF APPLIANCE FAILS TO LIGHT

Ÿ Make sure gas is turned on at cylinder.

Ÿ Make sure there is gas in the cylinder.

Ÿ Does the ignitor make a sparking noise?

If yes check for spark at burner.

If no spark check for damaged or loose wires.

Ÿ If wires are OK check for cracked or broken electrode,

replace if needed.

Ÿ If wire or electrodes are covered by cooking residue, clean

electrode tip with alcohol wipe if needed.

Ÿ If needed replace wires.

Ÿ If no sound check battery.

Ÿ Make sure battery is installed correctly.

Ÿ Check for loose wire connection at module and switch.

Ÿ If ignitor continues to not work then use match.

Leak Testing Valves, Hose and Regulator

Leak test before first use, at least once a year, and every time

the cylinder is changed or disconnected.

1. Turn all appliance control knobs to .

2. Be sure regulator is tightly connected to gas cylinder.

3. Turn on Gas. If you hear a rushing sound, turn gas off

immediately. There is a major leak at the connection.

Correct before proceeding.

4. Brush soapy solution (mixture of half soap and half water)

onto hose connections.

5. If growing bubbles appear, there is a leak. Turn off gas at

cylinder immediately and check tightness of connections. If

leak cannot be stopped do not try to repair. Call for

replacement parts.

6. Always turn off gas at cylinder after performing leak test.

Hot plate Match Lighting

• Do not lean over barbecue while lighting.

1. Turn gas burner control valves to (off).

2. Open lid during lighting or re-lighting.

3. Turn ON gas at LP cylinder.

4. Place lit match near burner. Immediately turn hot plate knob

to the HIGH position. Be sure burner lights and stays lit.

NOTE: Your barbecue may NOT be equipped with a

Hot plate!

Hot plate Ignitor Lighting

•Do not lean over barbecue while lighting.

1. Turn gas burner control valves to (off).

2. Open lid during lighting or re-lighting.

3. Turn ON gas at LP cylinder.

4. Turn hot plate knob to the  HIGH position, push and hold

ELECTRONIC IGNITOR button.

5. If hot plate does NOT light within 5 seconds, turn knob to

(off), wait 5 minutes, then repeat lighting procedure.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Char-Broil Performance 440 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info