Cleaning the Burner
Follow these instructions to clean and/or replace parts of
burner assembly or if you have trouble igniting grill.
1. T
2. Remove cooking grates and emitters.
3. Remove carryover tubes.
4. Detach electrode from burner
5. Carefully lift each burner up and away from valve
openings.
We suggest three ways to clean the burner tubes. Use
the one easiest for you.
well) into a small hook. Run the hook through each
burner several times.
B. Use a narrow bottle brush with a flexible handle (do
not use a brass wire brush), run the brush through
each burner tube several times.
C. Wear eye protection: Use an air hose to force air
into the burner tube and out the burner ports. Check
each port to make sure air comes out each hole.
6. Wire brush entire outer surface of burner to remove food
residue and dirt.
7. Clean any blocked ports with a stiff wire such as an open
paper clip.
8. Check burner for damage, due to normal wear and
corrosion some holes may become enlarged. If any large
cracks or holes are found replace burner
VERY
openings. See illustration below.
9.
10. Carefully replace burners.
1
12. Reposition carryover tubes and attach to burners.
Replace emitters and cooking grates.
Storing Y
•Clean cooking grates.
•Store in dry location.
•When gas cylinder is connected to appliance, store
outdoors in a well-ventilated space and out of reach
of children.
•Cover appliance if stored outdoors.
•Store appliance indoors ONL
off and disconnected, removed from appliance and
stored outdoors.
•When removing appliance from storage check for burner
obstructions.
General appliance Cleaning
•Do not mistake brown or black accumulation of
grease and smoke for paint. Interiors of gas grills
are not painted at the factory (and should never be
painted).
water or use a appliance cleaner with scrub brush on
insides of appliance lid and bottom. Rinse and allow
to completely air dryDo not apply caustic
appliance/oven cleaner to painted surfaces.
Høyre
skinne
• Plastic parts: Wash with warm soapy water and wipe
dry
• Do not use citrisol, abrasive cleaners, degreasers or a
concentrated appliance cleaner on plastic parts.
Damage to and failure of parts can result.
•Porcelain surfaces: Because of glass-like
composition, most residue can be wiped away with
baking soda/water solution or specially formulated
cleaner
stubborn stains.
•Painted surfaces: Wash with mild detergent or
nonabrasive cleaner and warm soapy water
dry with a soft nonabrasive cloth.
•Stainless steel surfaces: T
appliance’s high quality appearance, wash with mild
detergent and warm soapy water and wipe dry with
a soft cloth after each use. Baked-on grease
deposits may require the use of an abrasive plastic
cleaning pad. Use only in direction of brushed finish
to avoid damage. Do not use abrasive pad on
areas with graphics.
• Cooking surfaces: If a bristle brush is used to clean
any of the appliance cooking surfaces, ensure no
loose bristles remain on cooking surfaces prior to
grilling. It is not recommended to clean cooking
surfaces while appliance is hot.
Clean appliance often, preferably after each
cookout. If a bristle brush is used to clean any of the
appliance cooking surfaces, ensure no loose bristles
remain on cooking surfaces prior to grilling. It is not
recommended to clean cooking surface while
appliance is hot.
appliance should be cleaned at least once a year
•
IF
Make sure gas is turned on at cylinder
Make sure there is gas in the cylinder
Does the ignitor make a sparking Noise?
If yes check for spark at burner
If no spark check for damaged or loose wires.
If wires are OK check for cracked or broken electrode,
replace if needed.
If wire or electrodes are covered by cooking residue,
clean electrode tip with alcohol wipe if needed.
If needed replace wires.
If no sound check battery
Make sure battery is installed correctly
Check for loose wire connection at module and switch.
If ignitor continues to not work then use match.
Leak T
Regulator
1. T
2. Be sure regulator is tightly connected to gas
cylinder
3. Trushing sound , turn
gas off immediately
the connection. Correct before proceeding.
4. Brush soapy solution (mixture of half soap and
half water) onto hose connections.
Leak test before first use, at least once a
year and every time the cylinder is
changed or disconnected.
CA
SPIDER ALERT!
SPIDER AND WEBS
INSIDE BURNER
If your barbecue is getting hard to light or the
flame is weak, check and clean the venturis and
burners.
Spiders or small insects are known to create
“flashback” problems by building nests and laying
eggs in the barbecue’s venturi or burner
obstructing the flow of gas. The backed-up gas
can ignite behind the control panel. This
flashback can damage your barbecue and cause
injury
performance, the burner and venturi tube
assembly should be removed and cleaned
whenever the barbecue has been idle for an
extended period of time.
T
3
Firebox
Carryover
tube
Electrode
Firebox
burner
bracket
Pry off electrode
with a flat blade
screwdriver
Main Burner Ignitor Lighting
Do not lean over grill while lighting.
1. Turn all control knobs to .
2. Turn ON gas at LP
3. Open lid during lighting .
4. THI .
5. Push and hold ELECTRONIC IGNITION button
until the burner lights (use flame viewing ports to
verify).
6. If ignition does NOT occur in 5 seconds, turn the
control knobs , wait 5 minutes, and repeat the
lighting procedure.
7. Ignite remaining burners by repeating steps 4 through
6 for each burner
8. Once each burner has ignited, turn control knobs to
desired setting.
Viewing ports
Main Burner Match-Lighting
Do not lean over grill while lighting.
1. Turn all control knobs to .
2. Open lid . TON gas at LP cylinder.
3. Place match into match holder (hanging from left side
of cabinet). Light match; then light burner by placing
match through the match light hole on left side of grill.
4. Push in and turn far left knob to the HI position. Once
burner has ignited (use flame viewing ports to verify),
turn control knob to desired setting.
5. If ignition does not occur in 5 seconds, turn the control
knob to , wait 5 minutes, and repeat the lighting
procedure.
6. Light adjacent burners in sequence by pushing control
knobs in and turning to the HI position.
WARNING
Correct
burner-to-valve
engagement
5. If growing bubbles appear
gas at cylinder immediately and check tightness of
connections. If leak cannot be stopped do not try
to repair
6. Al
le
Retainer
clip
Connections
