Bedienungsanleitung Charnwood Bay 5 GT (Seite 17 von 28) (Englisch)

815479

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

FITTING THE OPTIONAL BASE ASSEMBLY

BAY 5 & 5GT

1. With the firebox removed, roll the outer convection casing onto its

back and fasten the assembly into position using four M6x20 screws

and nuts. Insert the screws through the holes in the underside of the

casing from the inside and fit the nuts onto the outside of the base.

Do not fully tighten the screws at this stage.

2. Attach the lower fireplace trim into position onto the base frame.

This part replaces the lower trim piece (002/MR113). Use two

M8x10 screws and finger tighten them to allow adjustment.

3. Undo the foot adjustment screws on the base assembly so that

they are just below the lower level of the base frame. Stand the

whole assembly up onto the base and trial fit into the fireplace

opening. Adjust the feet to overcome any rocking, should the

fireplace floor be uneven.

4. Trial fit the side trim pieces (002/XR112 or 002/MR112) and

adjust the lower fireplace trim position to obtain a good fit. Once

everything is aligned, tighten all fasteners.

PRE LIGHTING CHECK

Before initial lighting check the following points:

1. The bottom grate bars must all be fitted and should move freely

and easily when the riddling mechanism is operated.

2. The plates round the sides and back of the grate must be in

position and sitting correctly.

3. The throat plate must be fitted in the roof of the appliance (as

shown in Fig. 8).

4. Check that the front fence is fitted correctly and that the door

closes properly.

COMMISSIONING

On completion of the installation allow a suitable period of time for

the fire cement and mortar to dry out before commissioning the fire.

Before lighting, first check that there is an updraft in the chimney -

open the door of the stove and hold a lit match at the top of the door

opening. If the flame is pulled into the stove this indicates that there is

an updraft and the fire may be lit. If the flame is pushed out from the

stove then this indicates that a downdraft is present, the flue will need

to be warmed to produce an updraft and then checked using the

same procedure with the lit match. The flue may be warmed by

lighting a single sheet of newspaper, or a firelighter, within the stove

before attempting to light a proper fire. Sometimes it may be

necessary to open a window to give an initial draw.

A spillage test must be carried out to confirm safe operation with

doors and windows closed and any extract fans in operation (i.e.

worst conditions) Warm the appliance and flue before carrying out

the spillage test. Light a smoke match from the middle of a bed of

embers, hold the match approximately 20mm above the ember bed

and ensure that the smoke is carried up the flue and emitted safely.

Also check all joints and seals. On sucessful completion of the spillage

test please leave the operating instructions and tools with the

customer and advise them on the use of the appliance. If the spillage

test fails the cause must be found and rectified, or the appliance

decommissioned and the customer instructed not to use the

appliance untill it can be shown to operate safely.

CAA AND SMOKE CONTROL

The Clean Air Act 1993 and Smoke Control Areas

Under the Clean Air Act local authorities may declare the whole or

part of the district of the authority to be a smoke control area. It is an

offence to emit smoke from a chimney of a building, from a furnace

or from any fixed boiler if located in a designated smoke control area.

It is also an offence to acquire an "unauthorised fuel" for use within a

smoke control area unless it is used in an "exempt" appliance

("exempted" from the controls which generally apply in the smoke

control area).

The Secretary of State for Environment, Food and Rural Affairs has

INSTALLATION INSTRUCTIONS

charnwood

BAY

Lower fireplace trim

Base

Assembly

M8 Nut

Side Trim Piece

Convection Casing

M8x10

Screws

M8x20 Screws

Top Trim Piece

Fig. 13 Fitting the optional base assembly

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Charnwood Bay 5 GT Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info