Bedienungsanleitung Charnwood Bay 5 VL (Seite 11 von 28) (Englisch)

815477

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

UNPACKING THE STOVE

The stove arrives bolted and strapped to its pallet. There must be

adequate facilities for unloading and manoeuvring into position. The

convection casing is first removed from the top of the stove. The

stove is released from the pallet by removing the pallet bolts using a

10mm Spanner. The pallet brackets can now be removed from the

pallet and the stove can now be moved to its final position. The pallet

is intended to be cut up and used for kindling fuel.

HEALTH AND SAFETY PRECAUTIONS

Please take care when installing the stove that the requirements of

the Health and Safety at Work Act 1974 are met. Adequate facilities

must be available for loading, unloading and site handling.

Some types of fire cement are caustic and should not be allowed to

come into contact with the skin. In case of contact, wash with plenty

of water.

If there is a possibility of disturbing any asbestos in the course of

installation then please use appropriate protective equipment.

There must not be an extractor fan fitted in the same room as the

stove as this can cause the appliance to emit fumes into the room.

The combustion air supply ducting must be connected to a suitable,

permanently open air inlet. See ‘Air supply’ section for details. This

stove is capable of intermittent operation. This stove is not suitable

for use in a shared flue system.

In addition to these instructions the requirements of BS 8303 and

BSEN 15287-1:2007 must be fulfilled. Local Authority Bylaws and

Building Regulations given in approved document J, including those

referring to national and European Standards, regarding the

installation of Solid Fuel burning appliances, flues and chimneys must

also be observed.

The installation of any electrical services must be carried out by a

registered competent electrician and in accordance with the

requirements of the latest issue of BS 7671

CO ALARMS

Building regulations require that whenever a new or replacement

fixed solid fuel or wood/biomass appliance is installed in a dwelling a

carbon monoxide alarm must be fitted in the same room as the

appliance. Further guidance on the installation of the carbon

monoxide alarm is available in BS EN 50292:2002 and from the

alarm manufacturer's instructions. Provision of an alarm must not be

considered a substitute for either installing the appliance correctly or

ensuring regular servicing and maintenance of the appliance and

chimney system.

SPECIFICATION

In order for the appliance to perform satisfactorily the chimney

height must not be less than 4 metres measured vertically from the

outlet of the stove to the top of the chimney. The internal dimensions

of the chimney MUST NOT BE LESS THAN 150 mm (6 inches).

If an existing chimney is to be used it must be swept and checked, it

must be in good condition, free from cracks and blockages, and

should not have an excessive cross sectional area. If you find that the

chimney is in poor condition then expert advice should be sought

regarding the necessity of having the chimney lined. If it is found

necessary to line the chimney then a lining suitable for Solid Fuel must

be used.

If the stove has been fitted in the place of an open fire, it is

recommended that the chimney is swept one month after installation

to clear any soot falls which may have occurred due to the difference

in combustion between the stove and the open fire.

If there is no existing chimney then a prefabricated block chimney or

a twin walled insulated stainless steel flue to BSEN 15287-1:2007 can

be used either internally or externally. These chimneys must be fitted

in accordance with the manufacturers instructions and Building

Regulations.

Single wall flue pipe is suitable for connecting the stove to the

chimney but is not suitable for using for the complete chimney.

It is important that there is sufficient draw in the chimney and that

the chimney does not suffer from down-draught. When the chimney

is warm the draw should be not less than 1.3mm (0.05 inches) water

gauge (12.5 Pa). If it is found that there is excessive draw in the

CHIMNEY

INSTALLATION INSTRUCTIONS

charnwood

BAY

Output

Bay 5

Bay 5 GT

Bay 5 VL

5kW

(17,061BTU/h)

5.8kw

(19,790 BTU/h)

5kW

(17,061BTU/h)

Mass

94.3kg

105kg

94.3kg

Flue Gas

Temperature

279°C

286°C

279°C

Flue Gas

Mass Flow

4.1g/s

4.8g/s

4.1g/s

Average

Refuelling

Cycle

0.75hrs

Maximum

Log Size

Length 480mm

Diameter 75mm

Length 480mm

Diameter 75mm

Length 480mm

Diameter 75mm

Outputs were achieved burning seasoned hardwood logs over a 45 minute

refuelling period.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Charnwood Bay 5 VL Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info