Bedienungsanleitung Charnwood Cove 2B (Seite 5 von 16) (Englisch)

632314

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

the slot in the top of the tool before lifting (See Fig.3). Care should

be taken to ensure that ash is cool before emptying it into plastic

liners or bins.

To make ash removal easier there is a special Charnwood ash carrier

available. This may be purchased from your supplier or, in case of

difficulty, from Charnwood.

When loading the stove take care not to smother the fire, instead fill

the firebox in two stages waiting between each stage for the flames

to appear above the fire.

After a period of slumbering always turn the air control up to

maximum and wait until flames appear above the fuel bed before

opening the doors.

Burning coal will produce more soot deposits than other fuels,

especially if the fire is run at low levels for long periods. It is therefore

vital to clean the throat plate regularly, weekly cleaning is

recommended. Please also note that some blackening of the glass

may occur when burning coal.

Never fully close the Airwash control when burning coal.

The grate should be kept in the wood burning position and should

not be riddled until the ash becomes so deep that it begins to block

the passage of air into the firebox at the side of the grate. When this

is the case do not remove all of the ash using the riddling mechanism

but keep a layer about half an inch thick as this enables the wood to

burn more effectively. When burning wood or peat use the airwash

control in the same way as described (see "CONTROLLING THE

FIRE")

SPECIAL POINTS WHEN BURNING COAL

SPECIAL POINTS WHEN BURNING

WOOD AND PEAT

When lighting the fire a few small dry logs with a good

amount of kindling will help to get the fire up to temperature quickly.

OVERNIGHT BURNING

MAINTENANCE

For overnight burning the fire doors must be closed. Use large logs

rather than small ones.

If the fire is very low then it may be necessary to add a little fuel and

turn the thermostat control up to maximum for a brief period until

the fire is burning brightly before filling with fuel. When the new fuel

has ignited, the thermostat control should be turned down to the

required setting. If the central heating pump is off overnight then the

thermostat may be left at the same setting for both day and night

operation. If the central heating pump is on overnight then set the

thermostat control to give the required level of heating. Some

experimentation will be necessary to find the settings most suitable

for the particular fuel used and the draw on the chimney.

To revive the fire, add some small logs and open the thermostat

control to maximum. When the fire is burning well load on more fuel

as necessary and move the thermostat control to the desired setting.

The stove is finished with a high temperature paint which will

withstand the temperatures encountered in normal use. This may be

cleaned with a damp lint-free cloth when the stove is cold. Should re-

painting become necessary then special high temperature paints are

available from your supplier or from Charnwood.

The glass in the door is a special ceramic glass which is able to

withstand high temperatures. Before cleaning the glass open the door

and allow it to cool. Clean the glass using a damp cloth and then wipe

over with a dry cloth. Any stubborn deposits on the glass may be

removed with a proprietary stove glass cleaner or ceramic hob

cleaner. Some deposits on the glass may be burnt off simply by

running the fire at a fast rate for a few minutes. Do not use abrasive

cleaners or pads as these can scratch the surface which will weaken

the glass and cause premature failure. Aerosol spray cleaners should

not be used near the appliance whilst it is under fire.

If the fire is going to be out of use for a long period (for instance in

the summer) then to prevent condensation, and hence corrosion, the

air control should be left fully open and the fire door left ajar. It is

also advisable to sweep the chimney and clean out the fire. Spraying

the inside of the door and firebox with a light oil, such as WD40, will

also help to keep all internal parts working well.

After long periods where the fire has been out of use, the chimney

and appliance flueways should be cleaned before lighting.

Cleaning

Cleaning the Glass

When Not in Use

Fig. 3. Ashpan Removal

Tongue must be visible to

ensure correct tool location.

charnwood

OPERATING INSTRUCTIONS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Charnwood Cove 2B Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Charnwood Cove 2B

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info