Bedienungsanleitung Charnwood Island I (Seite 10 von 20) (Englisch)

632320

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

HEARTH AND FIRE SURROUND

CONNECTIONS TO FLUES

The stove arrives bolted and shrink-wrapped to its pallet which is

intended to be cut up and used for kindling fuel.

The stove must stand on a fireproof hearth and combustible

materials must not be used in the construction of the fireplace unless

adequately fireproofed in accordance with local building regulations.

The hearth must be at least 12mm (0.5inches) thick. The positioning

of the stove and the size of the hearth are governed by building

regulations for Class 1 appliances. These building regulations state

that the hearth must extend in front of the stove by at least 300mm

(12 inches) and to the sides of the stove by at least 150mm (6

inches). If in doubt as to the positioning of the stove expert advice

should be sought either from the supplier or the local building

inspector.

The fireplace must allow good circulation of air around the appliance

to ensure that maximum heat is transferred to the room and also to

prevent the fireplace from overheating. A gap of 150mm (6 inches)

each side and 300mm (12 inches) above the appliance should give

sufficient air circulation. If a wooden mantelpiece or beam is used in

the fireplace it should be a minimum of 460mm (18 inches), and

preferably 600mm (24 inches) from the appliance. In some situations

it may be necessary to shield the beam or mantelpiece to protect it.

In order for the fire to operate correctly there must be an air gap

behind the appliance of at least 40mm, but be aware that this

distance will need to be greater in some cases to meet Building

Regulation requirements.

There are several ways of connecting the stove to the flue. These are

illustrated in figures 4 to 7.

If a top flue connection (as shown in Fig. 6) or the vertical rear flue

connector (shown in Fig. 7) are used, then the chimney may be swept

through the appliance.

Horizontal lengths of flue must be kept to a minimum and should not

be more than the flue diameter. The sealing face of the flue collar

should be coated with fire cement before fixing to the body of the

stove using the two screws provided. The blanking plate must be

removed, sealed with fire cement and refitted, care being taken to

ensure that the fold on the clamping plate is in line with the lugs on

the firebox as shown on the label on the clamping plate. Ensure that

the clamping plate does not prevent the throat plate from seating

correctly. All flue connections must be well sealed.

With Soot Door

Alternative

Soot Door Positions

Fig. 6. Horizontal Register Plate With Top Flue Connection

With Soot Door

Alternative

Soot Door Positions

Fig. 5. Horizontal Register Plate With Rear Flue Connection

Soot Door

In Side or Rear

Of Chimney

Fig. 4. Vertical Register Plate With Bricked Up Fireplace

INSTALLATION INSTRUCTIONS

charnwood

I S L A N D

IIIII

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Charnwood Island I Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Charnwood Island I

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info