Bedienungsanleitung Charnwood Island II ct (Seite 9 von 16) (Englisch)

632323

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

HEALTH AND SAFET Y PRECAUTIONS

CHIMNEY

Please take care when installing the stove that the requirements of

the Health and Safety at Work Act 1974 are met.

Some types of fire cement are caustic and should not be allowed to

come into contact with the skin. In case of contact wash with plenty

of water.

If there is a possibility of disturbing any asbestos in the course of

installation then please use appropriate protective equipment.

There must not be an extractor fan fitted in the same room as the

stove as this can cause the appliance to emit fumes into the room.

If an existing chimney is to be used it must be swept

and checked, it must be in good condition, free from cracks and

blockages, and should not have an excessive cross sectional area. If

This is particularly necessary if

the room is double glazed. It must be positioned such that it is not

liable to blockage.

This stove is not suitable for use in a shared flue system.

In addition to these instructions the requirements of BS.8303 and

BS EN15287-1:2007 must be fulfilled. Local Authority Bylaws and

Building Regulations, including those referring to National and

European Standards regarding the installation of Solid Fuel burning

appliances, flues and chimneys must also be observed.

Building regulations require that whenever a new or replacement

fixed solid fuel or wood/biomass appliance is installed in a dwelling a

carbon monoxide alarm must be fitted in the same room as the

appliance. Further guidance on the installation of the carbon

monoxide alarm is available in BS EN 50292:2002 and from the

alarm manufacturer's instructions. Provision of an alarm must not be

considered a substitute for either installing the appliance correctly or

ensuring regular servicing and maintenance of the appliance and

chimney system.

In order for the appliance to perform satisfactorily, the chimney

height must not be less than 4 metres measured vertically from the

outlet of the stove to the top of the chimney. The chimney must not

be less than 150 mm (6 inches) internal diameter or 150 x 150mm

internal square.

CO ALARMS

There must be an adequate air supply into the room in which the

appliance is installed to provide combustion air. The combustion air

supply for Island IIct must be via a permanently open vent. The

minimum free area is .16.5cm (2.5 in )

you find that the chimney is in poor condition then expert advice

should be sought regarding the necessity of having the chimney lined.

If it is found necessary to line the chimney then a lining suitable for

Solid Fuel must be used.

If there is no existing chimney then a prefabricated block chimney or

a twin walled insulated stainless steel flue to BS EN15287-1:2007 can

be used either internally or externally. These chimneys must be fitted

in accordance with the manufacturers instructions and Building

Regulations.

Anki pumice liners or chimney blocks will give a highly insulated

chimney which will work well with all fuels. For details ring Anki

Chimney Systems on (01983) 527997.

Single wall flue pipe, of diameter no less than the stove outlet, is

suitable for connecting the stove to the chimney but is not suitable

for using for the complete chimney.

If it is found that there is excessive draw in the chimney then a

draught stabilizer should be fitted.

It is important that there is sufficient draw in the chimney and that

the chimney does not suffer from down-draught. When the chimney

is warm the draw should be not less than 0.10 inches water gauge

(25Pa). If in doubt about the chimney seek expert advice.

HEARTH AND FIRE SURROUND

The stove arrives bolted and shrink-wrapped to its pallet which is

intended to be cut up and used for kindling fuel.

The stove must stand on a fireproof hearth and combustible

materials must not be used in the construction of the fireplace unless

adequately fireproofed in accordance with local building regulations.

The hearth must be at least 12mm (0.5inches) thick. The positioning

of the stove and the size of the hearth are governed by building

INSTALLATION INSTRUCTIONS

charnwood

I S L A N D

SPECIFICATION

Island IIct

Output kW

(BTU/h)

8.0

(27,300)

Mass kg

(lb)

140

(309)

Flue Gas Temp °C

307

Flue Gas Mass Flow g/s

6.1

Max Hearth Temp °C

38.3

The outputs were obtained burning seasoned hardwood.

Specification

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Charnwood Island II ct Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Charnwood Island II ct

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info