Bedienungsanleitung Charnwood SLX 45 MKII - Multi fuel (Seite 13 von 20) (Englisch)

815485

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

FITTING THE FIRE

In some cases it may be necessary to place the connecting flue pipe

in the chimney before fitting the fire into the fireplace.

Apply fire cement to the rear face of the sealing flange on the

appliance. Fit the appliance into the opening ensuring that it is central

and that a good seal is made between the sealing flange and the face

of the surround.

Remove any excess fire cement from around the sealing flange. The

fire should be screwed to the hearth through the holes at the base

of the sealing flange.

Connect the heating system to the boiler ensuring that the primary

flow pipe rises from the appliance. Fill the system with water and

check for leaks.

FLUE CONNECTION AND INFILLING

Make the flue connection with a short length of 150mm (6’’)

internal diameter flue pipe (cast iron to BS41:1973, 1.0 mm thick

stainless steel, or 5.0mm thick mild steel).

The end of the flue pipe must line up with the centre-line of the

chimney, and must also extend to the point where the chimney

narrows to its final size. Any large voids must be filled and flaunched

to the flue pipe to ensure that all soot deposits can be cleared when

the chimney is swept. If necessary a flue offset is available. The offset

may be used directly with stainless steel flue pipe or may be used

with cast iron flue pipe in conjunction with a cast iron adaptor. If the

flue pipe has to be set at an angle then cut the ends so that it sits

correctly.

Ensure that the flue pipe is not obstructed or restricted in any way

and that all joints are well sealed.

Before infilling cover the front of the appliance to protect it. Ensure

that the flue pipe is central and then fill the space between the body

of the appliance and the structural brickwork with vermiculite (e.g.

Micafil or similar) concrete. Ensure that there are no air pockets.

The recommended mix is six volumes of vermiculite granules to one

volume of Portland cement thoroughly mixed together. Enough

water should be added so that no more than one or two drops of

water are released when a handful of the mixture is squeezed.

After filling with vermiculite flaunch the top of the flue connector

pipe to the chimney with lime mortar. Make good the holes in the

front and side of the chimney breast making sure that they are

completely airtight. A typical installation is shown in Fig. 9.

Fig. 9. Typical Installation into standard chimney

charnwood

INSTALLATION INSTRUCTIONS SLX4 5

MU LT I-F UEL

Vermiculite

Infill

Flaunching

Short Length

or Flue Offset.

Of Flue Pipe,

In most installations it will be possible to sweep the chimney through

the appliance. If this is not possible then some alternative means

(such as a soot door) must be provided.

The free inset method of installation may be used instead of infilling.

Details are available on request.

2. INSTALLATION AS A

FREESTANDING STOVE

The SLX45 may be installed as a Freestanding Stove when supplied

with the Freestanding Panel Pack 020/KV52. Typical installations are

shown in Figs. 10 & 11 and may be either on a freestanding hearth

or in an ‘Inglenook’ type fireplace. In these configurations the

minimum distances to combustible materials must be 200mm from

the sides of the stove and 300mm from the back. Stud wall is

counted as combustible, and if this distance is required to be

reduced, then additional shielding must be provided.

The Hearth requirements are the same as the Inset Installation.

If the stove is to be installed on a freestanding hearth, as shown in

Fig.10, then the fireplace may be bricked up and filled with non-

combustible material, and the chimney breast broken into higher up

the wall, and a sleeve inserted to take the Fluepipe. The angle

between the vertical and the sleeve/fluepipe must be not less than

135°. It is advisable for the vertical section of the Fluepipe to be at

least 600mm long. A soot door for debris clearance/ chimney

sweeping must be provided and this may be in the side or front of

the chimney breast, or outside.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Charnwood SLX 45 MKII - Multi fuel Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info