Bedienungsanleitung Charnwood SLX20 (Seite 11 von 20) (Englisch)

815482

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Vermiculite

Infill

Flaunching

Take Flue Pipe

Up To Narrowest

Part Of Chimney.

150° Elbow

Part No. 010/AV12

Fig. 4. Typical Inset Installation into standard chimney

150°

Fig. 3. Limiting Dimensions Of Surround And Opening

Dim. A:

Dim. B:

Max. 575mm (22 2/3")

Min. 555mm (21 3/4")

Max. 470mm (18 1/2")

Min. 405mm (16")

The shaded area on the face of

the surround is the minimum flat

area required for Inset Installation.

660 mm

750 mm

charnwood

INSTALLATION INSTRUCTIONS SLX20

MU LTI-FUEL

order for the appliance to fit into the fire surround there must be a

flat area around the opening, details are shown in Fig. 3.

PREPARATION OF THE FIREPLACE

Before fitting the appliance into an existing fireplace remove the fire

back and any loose in-fill material.

The surround and opening for the appliance must conform with

Fig.3. The flat area around the opening must be a minimum of

750mm wide and 660mm high. Ensure that the hearth and the base

in the opening are flat, level, and at right angles to the surround.

Make a hole in the font of the chimney breast to give access for

infilling and fixing the flue pipe. If the optional boiler is to be fitted it

will also be necessary to make a hole in the side of the chimney

Single wall flue pipe is suitable for connecting the appliance to the breast to give access for the pipework.

chimney but is not suitable for using for the complete chimney.

FITTING THE FIRE

If it is found there is excessive draw in the chimney then a draught

stabiliser should be fitted.

The SLX 20 is supplied with one of two panel packs that makes it

either an Inset stove SLX20i or a Freestanding stove SLX20fs. The

following sections apply specifically to the Inset Installation. The

Freestanding installation is mentioned later.

The appliance must be installed on a fireproof hearth. The

positioning of the appliance and the size of the hearth are governed

by building regulations for Solid Fuel appliances. These building

regulations state that the hearth must extend in front of the

appliance by at least 300mm (12 inches) and to the sides by at least

150mm (6 inches). If in doubt as to the positioning of the appliance,

expert advice should be sought, either from the supplier or the local

building inspector.

The fireplace must allow sufficient airflow around the appliance to

provide combustion air and to allow the heat to be transferred to the

room. The fire surround must be able to withstand the temperatures

generated in normal use. Resin based conglomerates are not suitable

and must not be used. If a wooden mantel is used it should be at least

300mm (12 inches) above the appliance. Wooden surrounds must

be at least 150mm (6 inches) from the sides of the appliance. In

1. INSTALLATION AS AN INSET STOVE

In some cases it may be necessary to place the connecting flue pipe in

the chimney before fitting the fire into the fireplace.

Apply fire cement to the rear face of the sealing flange on the

appliance. Fit the appliance into the opening ensuring that it is central

and that a good seal is made between the sealing flange and the face

HEARTH AND FIRE SURROUND

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Charnwood SLX20 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info