Bedienungsanleitung Charnwood SLX20 (Seite 14 von 20) (Englisch)

815482

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

charnwood

INSTALLATION INSTRUCTIONS SLX20

MU LTI-FUEL

THERMOSTAT

Before lighting the fire check the cold setting distance of the

thermostat. With the control knob at the minimum setting the flap

should be just closed as shown in Fig. 9. To adjust the distance slacken

the locking nut and adjust as necessary. When set correctly re-tighten

the locking nut. Ensure that the flap opens and closes freely as the

knob is turned.

Fit the side panels and the hood onto the appliance. Instructions for

this are enclosed with the panel pack. Replace any internal parts

previously removed.

PRE LIGHTING CHECK

Before initial lighting check the following points:

1. The bottom grate bars must all be fitted and should move freely and

easily when the riddling mechanism is operated.

2. The plates round the sides and back of the grate must be in position

and sitting correctly.

3. The throat plate must be fitted in the roof of the appliance.

COMMISSIONING

On completion of the installation and after allowing time for the fire

cement and mortar to dry out, the fire should be lit and checked to

ensure that the smoke and fumes are taken from the appliance up the

chimney and emitted safely. Also check all joints and seals.

On completion of the installation and commissioning please leave the

operating instructions with the customer and advise on the use of the

appliance.

ASSEMBLY

positioning the appliance in the fireplace if the fire surround is already

fitted.

Before fitting the boiler, remove the front firebars, the side and back

fire plates and the firebricks. Knock out the knock-outs for the boiler

tappings on the appropriate side of the firebox.

Remove the backnuts and fibre washers from the boiler tappings and

fit the boiler into the appliance. Place the fibre washers over the

tappings on the outside of the appliance and fit the backnuts,

ensuring that the boiler is held tightly against the rear inside face of

the appliance and that the top edge of the boiler is level or runs uphill

to the flow tapping.

When re-fitting the firebricks, note that the short side firebrick

supplied with the boiler must be fitted on the same side as the boiler

tappings. One of the original sidebricks is fitted on the other side, and

the rear brick is discarded. The firebricks are held in position by the

retaining brackets.

Replace the back fireplate, the side fireplates, the front firebar and

the throat plate.

Connect the boiler to the heating system ensuring that the flow pipe

rises from the boiler. Fill the system with water and check for leaks.

Thermostat Flap

Locking Nut

Flap Just Closed With

Knob Set To Minimum

Fig. 9. Thermostat Setting

Drain Cock at Lowest Point

Drain Cock

Gravity Return 28mm

Gravity Flow 28mm

Indirect Hot Water Cylinder

Cold Water Tank

Overflow

Feed and Expansion Tank

22mm Open Vents

Overflow

Domestic Hot Water Draw Off

Fig. 8. Typical Gravity Hot Water System

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Charnwood SLX20 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info