Bedienungsanleitung Chauvin Arnoux PEL104 (Seite 8 von 52) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch, Finnisch)

747191

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

07-2020

693779B00 - Ed. 1

CONFIGURING THE INSTRUMENT

To congure your PEL, select the instrument in the PEL Network directory.

Open the Configure the instrument dialogue box by clicking on the Configure icon in the toolbar, in the Instrument

menu, or in the Status zone.

This dialogue box has 6 tabs:

 General: Contains elds used to assign a name to the instrument and auto-o command, LCD display unit command,

operating button, clock adjustment, and SD card formatting options.

 Communication: Options concerning the Bluetooth link, the Ethernet network, the Wi-Fi and 3G-UMTS/GPRS.

 Measurement: Selection of the distribution system, ratio of voltages, and selection of the frequency

 Current sensor: Detection of the current sensors and choice of the nominal primary current.

 Recording: Recording parameter options.

 Meters: Reset of the meters and partial energy meter reset options.

 Alarms: programming of the alarms.

 Nominal values: dene the nominal values .

 L452: connect the Data Logger to the instrument (PEL104).

 Report: congure reports and send them by email

Click on OK to transfer the new conguration to the instrument.

STARTING RECORDING (START/STOP)

To start recording, do one of the following:

 In PEL Transfer: Select the appropriate option in the Recording tab of the Configuration dialogue box. The

instrument can be configured to start recording either at some future date and time, or immediately after recording

is configured on the instrument.

 On the instrument: Press the Selection button and hold it down until the REC indicator lights, then release it. The

instrument starts recording as it was previously configured to do.

To stop recording, do one of the following:

 In PEL Transfer: In the menu, select Instrument > Stop recording .

 On the instrument: Press the Selection button and hold it down until the REC indicator lights, then release it.

VIEWING THE RECORDING

The recorded data can be transferred to the PC in two ways and then be displayed there and used to create reports:

 The SD card can be withdrawn from the instrument and connected to the PC using the SD card reader provided.

Start PEL Transfer, select the Open command in the File menu, point to the ICP le bearing the desired session

number on the SD card, and select Open.

 Direct connection between the PC and the PEL (USB, Ethernet, Wi-Fi, or Bluetooth). Start PEL Transfer, open a

connection to the instrument, select the instrument (make sure that it is connected) in the tree, then select Recorded

sessions. Double-click on the desired recorded session. When the download is over, select the downloaded test

and click on the Open button in the Download dialogue box.

In both cases, the session is added to My open sessions in the tree. The data can then be displayed.

USER’S MANUAL

Visit our web site to download the operating instructions for your instrument:

www.chauvin-arnoux.com

Search on the name of your instrument. When you have found the instrument, go to its page. The operating instructions

are on the right. Download them.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Chauvin Arnoux PEL104 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info