Bedienungsanleitung Chicco Cosmos 2020 (Seite 13 von 108) (Alle Sprachen)

767883

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

lap section through the appropriate light blue guides

L, located at the rear of the Child Car Seat backrest;

then fasten the safety belt to the buckle of the seat.

(Diag. 8)

• Tension the lap section of the belt as much as pos-

sible, and insert it inside the appropriate guide O,

located on the same side where you are tting the

Child Car Seat. (Diag. 9)

• Check that the Child Car Seat is tightly and correctly

tted into the car seat, and that the safety belt is well

tensioned. If the Child Car Seat is not tightly and

safely tted into the car seat, repeat the installation.

(Diag. 10)

WARNING! Always check that all parts of the safety belt

are well tensioned and that it is not twisted.

WARNING! NEVER use the safety belt in positions other

than those indicated in these instructions.

HOW TO FIT THE CHILD CAR SEAT INTO THE CAR

FOR GROUP 1 (From 9 up to 18 kg)

WARNING! When it is used for Group 1 (from 9 up to

18 kg), always t the Child Car Seat in a forward-facing

direction.

If the Child Car Seat is tted in the front seat of the car,

it is recommended to push the seat back as much as

possible, bearing in mind the comfort of the passen-

ger sitting in the seat directly behind it, and to adjust

the backrest in the most vertical position.

If the car is equipped with a safety belt height adjuster,

x it in the lowest position. Then check that the car

seat safety belt adjuster is either in a backward posi-

tion with respect to the backrest of the car seat (or at

least aligned to it).

WARNING! The points through which the safety belt

must pass for tting for Group 1 (from 9 up to 18 kg)

are highlighted in RED.

Adjust the Child Car Seat to the most reclined position

(Diag. 6), with the handle K.

• Position the Child Car Seat on the selected car seat in

the forward-facing position. (Diag. 11)

• Hold the 3-point safety belt of the car and insert it

between the base and seat; then fasten it to the op-

posite side. (Diag. 12)

• Pass the horizontal section of the safety belt (lap

section) under the two red belt guides M. (Diag. 13)

• Tension the safety belt as much as possible, holding it

from the diagonal section (thoracic section). (Diag. 14)

• Press the button located on the locking clamp N, lo-

cated on the side where you are tting the child car

seat; then insert the diagonal section of the belt into

the clamp. Release the button, which will automa-

tically return to the lock position. Tension the safety

belt as much as possible. (Diag. 15)

• Insert the upper part of the diagonal belt inside the

guide O. )Diag. 16)

• Tension the belt as much as possible, ensuring that the

Child Car Seat adheres correctly to the car seat. If neces-

sary, carry out this operation exercising some pressure on

the Child Car Seat with your knee. (Diag. 17)

• Check that the Child Car Seat is tightly and correctly

tted into the car seat, and that the safety belt is well

tensioned. If the Child Car Seat is not tightly and

safely tted into the car seat, repeat the installation.

(Diag. 18)

WARNING! Always check that all parts of the safety belt

are well tensioned and that it is not twisted.

WARNING! NEVER use the safety belt in positions other

than those indicated in these instructions.

HOW TO ADJUST THE SAFETY HARNESS

WARNING! The safety harness must always be adjusted

to suit the child’s growth.

• To adjust the safety harness correctly, the straps must

come out from the backrest, at the height of the

child’s shoulders. (Diag. 19)

Adjust the safety harness as illustrated below:

Adjust the Child Car Seat to the most reclined position

with the handle K (Diag. 6).

• Press the belt adjustment button (F) and, at the same

time, hold the two child car seat harnesses (D) under

the shoulder straps and pull them towards you to sla-

cken them. (Fig. 20)

• Unfasten the safety harness, pressing the red button

on the buckle. (Diag. 21)

• Remove the two harness straps from the locking

plate P, located on the rear of the backrest. (Diag. 22)

• Pull the harness straps from the front to remove them

from the backrest and shoulder straps. (Diag. 23)

• Remove the shoulder straps, turning and removing

the locking plates from the respective holes on the

backrest. (Diag. 24)

• Reinsert the plates of the shoulder straps at the

desired height, inside the respective holes on the

backrest. (Diag. 25)

• Lock the two tabs into the buckle. This will help you

to check that the harness strap is inserted in the cor-

rect position. (Diag. 26)

• First insert the two harness straps through the shoul-

der straps; then insert them into the holes located on

the backrest and into the locking plates of the shoul-

der straps. (Diag. 27)

• Reinsert the two harness straps into the plate. (Diag. 28)

• Check that both the plate and harness straps are po-

sitioned as shown in the diagram. (Diag. 29)

WARNING! Check that the harness is not twisted.

SEATING THE CHILD IN THE CHILD CAR SEAT

Loosen and unfasten the harness of the Child Car Seat,

as illustrated in the “HOW TO ADJUST THE HEIGHT OF

THE SAFETY HARNESS” paragraph, Diag. 20 and 21.

• Sit the child in the Child Car Seat. (Diag. 30)

WARNING! Always check that the child is sitting with

its back correctly placed against the backrest of the

Chicco Cosmos 2020 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info