Bedienungsanleitung Chicco Essential Digital Audio Baby Monitor (Seite 20 von 148) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch)

500879

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

the power cord or plastic parts show signs of

damage, do not use them and contact a qualified

technician.

- Do not leave mains adapters (1) plugged into

the outlet when devices are not in use and/or not

connected to the mains adapters (1).

2.1.2 Modes of use - Switching on and

Adjustment

The child unit (primarily in transmitter mode)

must be positioned about 1 - 1.5 metres from

the child, on a flat, stable surface and with the

microphone (7) directed toward the child.

Attention: the transmitter, mains adapter and its

power cord must be kept out of reach of children.

• Child unit (primarily in transmitter mode) On/

Off button (2).

Press this button for about 3 seconds and the

child unit will switch on. Do not press for too long,

otherwise the child unit may not switch on. Press

this button (2) again for about 3 seconds and the

child unit will switch off.

• Night light On/Off button (4)

Press this button for about 3 seconds and

the nightlight (3) will switch on steady and at

minimum intensity.

Do not press for too long, otherwise the nightlight

(3) may not switch on.

If during this operating mode, you press the

nightlight On/Off button (4) once, the “Variable

brightness nightlight” mode will be activated.

Brightness will automatically vary from maximum

level to minimum level.

At the twelfth minute, nightlight brightness will

remain fixed at minimum level.

During the “Variable brightness nightlight”

operating mode, if the nightlight On/Off button

(4) is pressed once, light brightness will return

steady at minimum level.

If the nightlight On/Off button (4) is pressed

again in this operating mode, the brightness

variation cycle will begin again, starting from

maximum level.

Press the nightlight On/Off button (4) button

again for 3 seconds and the nightlight will switch

off, both in minimum, steady brightness and in

“Variable brightness nightlight” mode.

For energy savings, when the child unit (primarily

in transmitter mode) is being powered via Alkaline

batteries, the nightlight, if in minimum intensity

and steady mode, switches off automatically 5

minutes after the end of the ‘Variable brightness

nightlight” operating mode cycle.

If the child unit (primarily in transmitter mode)

is being powered via mains adapter (1), the

nightlight will remain on in both modes until the

button (4) is pressed again for 3 seconds.

The nightlight can be switched on even when the

child unit is off.

2.1.3 Operating indicator lights

- The power and link indicator light (5) supplies 3

different pieces of information:

- Indication that the device is on and properly

connected to parent unit:

the indicator light (5) will light up steady green.

- Indication of loss or absence of link with the

parent unit during operation:

the indicator light (5) will light up green and

begin to flash.

As soon as the link with the parent unit is restored,

the indicator light (5) will light up steady green.

NOTE: when the child unit switches on, it

searches for the channel to link with the parent

unit; therefore the indicator light (5) will flash

green until a link is established.

-Indication of device off:

the indicator light (5) will switch off.

- The Alkaline battery status indicator light (6)

supplies 2 different pieces of information:

-Indication that Alkaline batteries are almost flat:

the indicator light (6) will light up red and begin

to flash.

- Alkaline batteries charged or operation via

mains adapter (1):

the indicator light (6) will switch off.

2.2 Parent unit (primarily in receiver mode)

2.2.1 Power:

Power via supplied rechargeable 3.7V 800mAh

lithium-ion battery (13) or via 100-240V ~

50/60Hz /6V 500mA (1) mains adapter

ATTENTION. The charging of rechargeable

batteries should only be done via the supplied

mains adapter (1) and can be performed both if

the parent unit is switched on and if the parent

unit is off.

In the event of power with mains adapter (1) or

rechargeable lithium-ion battery charging:

- insert the mains adapter jack (1) in the power

connector (12) on the side of the unit.

- verify that the voltage corresponds to the rating

plate of the previously indicated adapters.

- insert the mains adapter plug in an easily

accessible power socket.

Warnings

- The mains adapter cord (1) may constitute a risk

of strangulation, keep out of reach of children.

- Periodically inspect mains adapters (1). If

the power cord or plastic parts show signs of

damage, do not use them and contact a qualified

technician.

- Do not leave mains adapters (1) plugged into

the outlet when devices are not in use and/or not

connected to the mains adapters (1)

2.2.2 Modes of use - Switching on and

Adjustment

• Parent unit (primarily in transmitter mode) On/

Off button (2).

Press this button (2) for about 3 seconds and the

parent unit will switch on. Do not press for too

long, otherwise the parent unit may not switch

on. Press this button (2) again for about 3 seconds

and the parent unit will switch off.

A beep will be heard when switching the parent

unit on and off.

• Loudspeaker volume adjustment buttons + and

- (3a-3b).

Press the button (3a) corresponding to the

symbol “+” once to increase volume by one

level. Press the button (3b) corresponding to

the symbol “-” once to decrease volume by one

level. The unit offers 10 volume setting levels. The

default level is 5.

A beep will be heard each time volume is increased

or decreased by a level. When volume reaches

maximum or minimum level, 2 consecutive beeps

will be heard.

The device stores the volume level selected

during previous use in its memory, even after it

has been switched off and switched back on.

• Voice activation or continuous transmission

ON/OFF selector.

The parent unit can work in continuous

transmission mode (selector in OFF position)

or in voice activation mode (selector in ON

position). In voice activation mode, the parent

unit loudspeaker (7) interrupts the reproduction

of any sounds emitted from the child that are

below the factory set default voice activation

threshold, while all sounds above the threshold

are reproduced.

Chicco Essential Digital Audio Baby Monitor Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info