Bedienungsanleitung Chicco Next 2 Me Magic (Seite 14 von 100) (Alle Sprachen)

767856

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

D7. Front strap fastening buckle

D8. Mattress stopper

D9. Side tilting button

D10. Crib structure side upright fasteners

E. Crib structure side uprights

F. Fastening straps

F1. Red crib front fastening buckle

F2. Grey crib rear fastening buckle

F3. Grey bed fastening and height adjustment buckle

G. Mattress with removable lining

H. Bag

ASSEMBLY OF THE CRIB

1. Hold the bottom support “A” and insert the lower bar “B” in the

relevant slot “A8” (Fig.1), pushing the metal pin until you hear

the click. Repeat the same operation for both feet.

2. Now insert the central support structure “C” into the slots “A7”

on both leg support, pushing the metal pin until you hear

the click (Fig. 2-3).

3. Hold the frame “D2” and turn the upper part of the frame by

90° (Fig.4). Repeat the same operation for the bottom of the

crib “D4” (Fig. 5).

4. Pass the side support uprights “E” through the openings

“D1.4”, on both sides of the crib (Fig.6), until they are inserted

into the fasteners “D10”, making sure that you have heard the

click of correct installation (Fig.7).

5. Close the vertical front zippers “D1.1” (Fig.8) and then the

upper hinge “D1.2” (Fig.9).

6. Fasten the buttons “D5” located in the upper front corners,

and in the front and rear areas of the bottom of the crib

(Fig.10-11-12).

7. Fasten the crib structure “D” to the feet “A” inserting the

uprights “E” inside the supports “A9” placed on both feet

(Fig.13), until you hear the click. Be careful to position the

structure D so that the tilting front panel faces in the same

direction as the telescopic feet “A5”.

8. Insert the mattress “G” inside the crib structure “D”, paying

attention to orient the breathable net surface upwards

(Fig.14). Make sure the mattress rests against the stopper “D7”

(Fig.14A).

9. Block the 4 wheels “A6” of the crib by lowering the levers that

activate the brakes (g.15). The crib is now ready to be used.

ADJUSTING THE CRIB HEIGHT

10. The crib can be adjusted in 11 dierent heights. To adjust

the height, press the buttons “A1” on the leg support “A” and

lift or lower the structure “D” to the desired position (Fig.16).

Release after hearing the click.

11. The base of the crib can be slightly inclined by adjusting the

leg supports to dierent heights (g.17).

WARNING: The crib can be inclined by a maximum of 4

positions between one leg support and the other (e.g., right leg

support in position 5 and left leg support in position 1 (Fig. 18).

WARNING: The child’s head must always be positioned near

the raised end (g.19).

WARNING: It is not possible to select dierent heights on the

two sides of the crib when in rocking conguration.

ROCKING FUNCTION ACTIVATION

12. You can activate the tilting function by pushing down the

buttons “A2” on the leg supports “A” (Fig.20). To deactivate

the function, return the buttons “A2” to their original

position, pushing them upwards.

WARNING: If the crib has been used previously in “Side

sleeping conguration (fastened to the bed),” make sure that

the side is in locked position and check that it is engaged

correctly.

WARNING: Always remember to deactivate rocking

conguration when using the product in “Side sleeping

(fastened to the bed)” or when the child is unattended.

WARNING: It is not possible to select dierent heights on the

two sides of the crib when in rocking function.

SIDE SLEEPING CONFIGURATION (FASTENED TO THE BED)

It is possible to fasten the crib to the parents’ bed (side sleeping

conguration).

WARNING - IMPORTANT FOR YOUR CHILD’S SAFETY: This

conguration is allowed only with beds that allow compliancy

with all the conditions described in this paragraph.

In particular, the LOWERED side of the crib must always be

positioned against the mattress of the parents’ bed and the

parents’ mattress must be aligned with the height of the

crib’s side (g.21). Moreover, the crib must be fastened to the

structure of the parents’ bed or to the mattress support (mesh

or slat sprung base).

WARNING: Check that the structure of the crib in side sleeping

conguration does not interfere with the parents’ bed.

WARNING: During use, make sure that the bedsheets, blankets,

etc. do not interfere with the crib’s space.

1. Lower the side of the crib by pushing button “D9” and

accompanying the side until it reaches the end of its travel

(Fig.22).

WARNING: Use the crib with the side lowered only in side

sleeping mode, (fastened to the bed).

2. Put the crib against the parents’ bed and check its height

compared to the parents’ mattress (Fig. 23).

WARNING: The height of the parents’ mattress must be higher

than or the same as that of the side of the crib, (fastened to

the bed). If this is not the case, use the adjustment system to

achieve this condition on both sides.

WARNING: In side sleeping conguration, the 2 leg supports

of the crib must be set at the same height.

3. To fasten the crib to the parents’ bed (side sleeping

conguration), use the pair of supplied straps “F”.

4. Carefully release the buckles “D6” and “D7” by pushing them

slightly upwards and then pulling them out (Fig.24).

5. Fasten the grey buckles “F2” to the buckles “D6” located in the

rear part of the bottom of the crib “D4” (Fig.25).

6. Fasten the red buckles “F1” to the buckles “D7” located in the

front part of the bottom of the crib “D4” (Fig.26).

7. Then pass the straps around the parents’ bed structure from

top to bottom (Fig.27) and fasten the grey buckles “F3” to

form a loop (Fig.28). Make sure to repeat the step on both

sides. To make installation easy, when fastening the buckles,

always keep the crib slightly away from the parents’ bed.

8. At this point put the crib against the parents’ bed and tighten

the noose pulling the straps (g.29). Carry out this step rst

on one side and then on the other, adjusting the straps until

the crib is in contact with the parents’ mattress.

WARNING: Before use, always make sure that there is no space

between the parents’ mattress and crib’s side. Otherwise adjust

the straps pulling them until the required condition is restored.

Make sure that the side is always free to be lowered and raised

completely.

9. Lock the crib’s wheels.

If when fastening the crib to the parents’ bed it is not possible

to t the crib’s feet under the parents’ bed, the crib can be

fastened anyway by the following the instructions above and

retracting the telescopic feet “A5” when putting the crib against

the bed.

To activate retraction, simply push the crib towards the bed so

Chicco Next 2 Me Magic Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info