Bedienungsanleitung Chicco Polly Swing Up (Seite 21 von 68) (Alle Sprachen)

767912

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

hear the metal pins click into place.

7. To assemble the seat on the frame, slide the oval shaped ends

of the connection tubes into the mobile slots on the X and Y x-

tures (Diagram 9). When you hear the metal pins click into place,

it means the seat is tted correctly. The assembling of the swing

frame has now been completed.

FITTING THE SAFETY HARNESS

8. Check that the upper harness straps are correctly slotted

through the slots in the fabric, as indicated in the previous para-

graph (point 4).

9. Slide the plastic rings into the slots on the bottom of the fabric

seat.

10. Slide the waist strap through the plastic rings located at the

bottom of the seat. Now use the relative clasps to fasten the

upper harness straps to the waist strap (Diagram 10).

11. Slide the two toothed ends into the buckle on the fabric crotch

strap (Diagram 11). The harness straps can be adjusted to dier-

ent lengths according to your child‘s build.

12. To assemble the dual tray on the swing, place the ends of the

tray on the side connection xtures and press until you hear it

click into place.

BOOSTER CUSHION

The swing can be used with a modular booster cushion which has

a section for the body and a headrest cushion.

13. To use the booster cushion, thread the upper harness straps

and the waist strap through the relative slots; now fasten the

upper straps to the waist strap using the relative clasps.

14. Thread the Velcro through the selected fabric slot to fasten the

headrest to the backrest. The headrest can be adjusted to two

dierent heights to adapt to the various growth phases whilst

guaranteeing comfort and protection.

15. Place the child in the swing and slide the two toothed ends

into the buckle (as seen in Diagram 12).

USING THE SUN HOOD

Polly Swing Up also has a practical sun hood: To assemble it:

16. Grasp the sun hood making sure the side with the slots for the

baby toys is facing the front of the swing.

17. Fasten the sun hood side xtures to the side hooks on the con-

nection tubes.

18. The position of the sun hood can be adjusted as necessary.

19. To remove the sun hood, gently pull the xtures towards the

inside of the swing until they are released.

ASSEMBLING AND USING THE REMOTE CONTROL

20. The remote control runs on 2 x 1.5 Volt LR03-AAA batteries and

can be used either attached or detached from the xture. See

Diagrams 13 and 14.

21. The remote control can be used to:

a) Switch the music and swinging motion ON and OFF;

b) Select 1 of the 4 swing speeds;

c) Select the nature sounds and tunes;

d) Adjust the volume.

SIDE FIXTURE WITH REMOTE CONTROL

22. A battery compartment (Diagram C1) is located inside the x-

ture X which powers the swing motion. It runs on 4 x 1.5 Volt

LR14 –C batteries.

23. There is a button inside the remote control compartment.

If swing mode is already being used:

a) Press and hold the button for 3 seconds to switch o the

music and the swing motion

If swing mode is turned OFF:

a) Press (quickly) and release the button once to start the

swing motion.

b) Press the button again to select the desired swing speed;

each time the button is pressed it will change the speed

from 1 to 4. On reaching the fastest speed, it will start from

1 speed again.

c) Press and hold the button for 3 seconds to switch o the

electronic mode.

Remember that the button on the remote control xture is only

used to start and stop the swing motion; it cannot be used to start

the nature sounds or tunes.

Gently push the seat to start the swing motion. Attention: Wait

for around 20 seconds to allow the swing motion to adjust to the

chosen setting.

24. If the swing motion stops, check whether:

a) The batteries are still working

b) The batteries are tted correctly

c) The weight of children is appropriate

d) The child is perhaps leaning forwards too much.

WARNING: The swing is tted with a safety device that stops the

motion after 30 minutes wait a couple of minutes before switching

it back on again.

VIBRATION BLOCK

25. The swing is tted with a vibration block (Diagram F3) which

can be activated by turning the knob to the “I” position. The vi-

bration block runs on 1 x 1.5 volt LR20-D battery.

REPLACING THE REMOTE CONTROL, SIDE FIXTURES AND VI-

BRATION BLOCK BATTERIES

26. To replace the remote control, side xture and vibration block

batteries; remove the screws from the various battery compart-

ment covers (Diagrams 15 and 16). Fit the new batteries mak-

ing sure they are tted with their poles in the right direction.

Now replace the compartment covers and rmly tighten the

screws.

FOLDING AWAY AND TRANSPORT

The swing can be folded up to store or transport it.

27. Press the side buttons on the X and Y xtures and close the

frame by pulling the front and rear legs towards each other.

(Diagram 17)

WARNING: Never use the sun hood to carry the swing.

*The theme of the removable toys varies according to the colour

coordination chosen.

WARRANTY

The product is guaranteed against any conformity defect in nor-

mal conditions of use as provided for by the instructions.

The warranty shall not therefore apply in the case of damage

caused by improper use, wear or accidental events.

For the duration of the warranty on conformity defects please refer

to the specic provisions of applicable national laws in the country

of purchase, where appropriate.

Chicco Polly Swing Up Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info