574369
6
Zoom out
Zoom in
Vorherige Seite
1/24
Nächste Seite
UK
3. Configuring the IRIS Touch Dialler
The majority of configurations can be carried out via the touch screen interface
display on the IRIS dialler. For more complex systems, for example where the data
port is used, additional configuration is available via the USB connector using a
laptop / PC and IRIS dialler configuration software (available via the Chiron website
at www.chironsc.com).
The touch screen display on the IRIS dialler provides an Installation Wizard which
guides you through a set of instructions for configuring the dialler. It is
recommended that you use this Wizard as it automatically carries out tests as you
proceed through the configuration.
Note: To select an option on the screen, touch the screen display.
Use the following procedure to configure the IRIS Touch Dialler:
1. Plug the power cable into the battery backed supply of the alarm panel. The
cable with the white stripe is the –ve connection. Ensure that the display on the
dialler becomes active.
The dialler carries out a self test and the Welcome screen then displays.
Note: If the power has been connected for the first time the Language menu
displays. Select the appropriate language from the list of languages available.
2. Select the
Installer Menu option from the Welcome screen.
Note: The default installer password is 111111.
3. Select the
Installation Wizard option from the Installation Menu.
4. Follow the remaining instructions on the screen to complete the configuration.
Note: During the installation procedure the Wizard shows the GSM/GPRS
signal strength. At this time the antenna position can be adjusted for optimum
signal.
(GSM / Ethernet & GPRS only).
Once the installation is completed successfully the message Status - System
OK is displayed on the Welcome screen and the LED Indicator on the top of the
unit is on steady.
Note: If the ‘Alarm Override’ mode is selected, the IRIS Touch Dialler replaces
the phone number and the account number used by the alarm dialler with the
IP address of the Monitoring Centre and Account Number entered during
configuration, so there is no need to change any settings on the alarm dialler. If
this is not appropriate (e.g. if the alarm dialler uses more than one account
number) then the telephone number dialed by the alarm dialler should be set to
the IP address of the Monitoring Centre in 12 digit format (e.g. 192.168.0.34
becomes 192168000034).
5. Carry out all the standard alarm signaling tests appropriate for the alarm
system.
6. Replace the cover on the alarm panel enclosure.
The installation is complete.
2 IRIS Touch 400 Range Dialler Quick Installation Manual (Version 1.0)
6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Chiron IRIS Touch 400 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Chiron IRIS Touch 400

Chiron IRIS Touch 400 Installationsanweisung - Englisch - 26 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info