Bedienungsanleitung Christopeit Basic-Concept 9881 (Seite 18 von 48) (Deutsch, Englisch, Holländisch, Französisch)

517196

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Step 9:

Installing the latissmus column (24), the weight slide (14), the stop slide

(58), the plastic inserts (12), the latissmus bar (16), the handle wrappings

(29), the cable (17) and the cable drum (18) with the screws (39), the

plastic spacers (56), the washers (52) and the self-locking nuts (49).

1. Place all parts named above accessibly in a free space.

2. Push the plastic inserts (12) onto the weight slide (14) and the stop slide

(58) at the top and bottom and push the two slides (14 + 58) from the

bottom onto the latissmus column (24), observing the direction of the

weight disc holder and the stop points.

3. Push the latissmus rest (66) in the opposite direction of the weight disc

holder on the latissmus column (24) and fasten ﬁ rmly with the screw

(38), the washer (52) and the nut (49).

4. Push a washer (52) and a plastic spacer (56) onto the screw (39), insert the

cable drum (18) in the latissmus column (24) with the holes corresponding

and ﬁ x in place by pushing in the screw (39). Push the second plastic

spacer (56) and a washer (52) onto the screw end and fasten ﬁ rmly with

the nut (49), ensuring that the plastic spacers (56) are not bent.

5. Push the cable (17) with an eye over the installed cable drum (18) through

the latissmus column (24) and joun the cable end to the weight slide (14)

with a carbine hook (45). Then join the other cable end with the second

carbine hook (45) to the latissmus bar (16).

6. Finally, push the spring circlip (27) on the bar bell weight holders of the

weight slide (14).

7. The latissmus column can be pushed into the foot (8) in the same way as

the curler console holder and fastened with the handgrip screw (31).

Step 8:

Installation of the curl trestle on the curler trestle holder with the screws

M8x15mm (41) and the washers 8//16mm (53).

1. Place the curl trestle (21) with the back upwards.

2. Put one spring washer (55) and one washer (53) on each screw (41).

3. Place the plate at the end of the curl trestle holder (9) so that the holes

in the plate and in the curl trestle (21) are aligned.

4. Push the screws (41) through the holes in the plate holder and screw

into the threaded holes in the curl trestle support and tighten ﬁ rmly.

5. Push the curl trestle holder into the foot (8) and secure in the desired

position by pushing in and tightening the handgrip screw (31).

(Note: The adjusted position can be changed as desired later and the

curl trestle unit can be installed or detached depending on the desired

exercise.

The leg curler (10) can also be secured and released according to the

desired exercise by pushing in or pulling out the securing clip (13)

beneath the handgrip screw (31) in the foot (8).)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Christopeit Basic-Concept 9881 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info