Bedienungsanleitung Christopeit BS5 - 1210 (Seite 16 von 48) (Deutsch, Englisch, Holländisch, Französisch)

644097

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Step 2:

Attach the front post (49) at main frame (1).

1. Push the handlebar support cover (51) onto the handlebar support (49).

2. Hold the handlebar support (49) with the computer cable (48) against the

main frame holder. Connect the plug for the computer cable (48) coming

out of the bottom of the handlebar support (49) with the matching plug

for the sensor cable (12) coming out of the main frame (1).

(Note: The computer cable harness (48) projecting from the support (49)

must not slide into the tube, as it is required for later steps of installation.)

3. Connect the cable of tension control (74) to the bracket of lower section

cable tension (75) (See ﬁgure [1]-[4]) Before this step of the installation,

it is advisable to adjust the resistance setting to the position, at which

the cable extends furthest from the sheath. Put the lowest part of cable

(74) into the small hook of lower tension cable (75) (ﬁgure 1+2). Pull it

(ﬁgure 3) until the small hook get in higher position (ﬁgure A3) and then

insert the cable (74) onto the bracket (75) (ﬁgure 4).

4. Place the handlebar support (49) in the locator provided for it in the main

frame (1). Ensure that the cable connections made are not squashed.

When putting the steering tube in place, push the former slowly down

into the locator in the main frame. Screw loosely the handlebar support

(48) onto the base frame (1) with the screws (39), spring washers (8) and

washers (7).(Attention: This screw connection will screw ﬁnal tightly in

step 3)

Assembly Instructions

Remove all the separate parts from the packaging, lay them on the

ﬂoor and check roughly that all are there on the base of the assembly

steps. Please note that a number of parts have been connected directly

to the main frame and preassembled. In addition, there are several

other individual parts that have been attached to separate units. This

will make it easier and quicker for you to assemble the equipment.

Step 1:

Attach the stabilizer (2+3) at main frame (1).

1. Attach the front foot (2) with the preassembled transport rollers (4) to the

main frame (1). Do this with the two screws M8x75 (6), curved washers

(7), spring washers (8) and cap nuts (9).

Attention: Mount the front foot into right direction, so that the transport

rollers don’t touch the ﬂoor during exercising.

2. Attach the rear foot (3) with height adjustable foot caps (5) to the main

frame (1). Do this with the two screws M8x75 (6), curved washers (7),

spring washers (8) and cap nuts (9). After assembly has been completed,

you can compensate for minor irregularities in the ﬂoor by turning the

eccentric cap (5). The equipment should be set up that the equipment

does not move of its own accord during a training session.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Christopeit BS5 - 1210 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info