Bedienungsanleitung Christopeit CRT 7100 (Seite 15 von 24) (Deutsch, Englisch)

793027

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

 Push the handgrip bars (5R) onto the connecng tubes (25R) and adjust

the holes in the tubes so that they are aligned. ( the handgrip bars must

be aligned aer assembly so that the upper ends are inclined outwards (away

from the support (30)).

 Push the screws (33) through the holes and ghten the handgrip bars (5)

with curved washers (31) and spring washer (32) rmly.

 Put the footrest holder (44R) at the connecng tube (25R) and adjust the

holes in the tubes so that they are aligned.

 Push the screw M8x78 (23) through the holes and ghten the footrest

holder (44R) at connecon tube (25R) with washers (27) and nut (26) rmly.

(This connecon point has to move easily. So please don’t ghten the screw

too much.)

 Place the preassembled unit of the right footrest holder (44R) and con-

necng tube (25R) at the right hand side of the main frame (40). ( Right

is specied as viewed standing on the machine during training.)





 Place screws M8x20 (33), curved washers (31) and spring washers

(32) accessibly beside the front part of the main frame (40).

 Place the lower end of the support (30) against the main frame

(40) and push the rubber ring (100) and support cover (101) onto the

support (30).

 Plug the ends of the two computer cables (34-38) projecng from

(30+40) together. ( The connecon cable (34) projecng from

the support (30) must not slide into the tube, as it is required for later

steps of installaon.) When joining the tubes, ensure that the cable

connecon will not trapped.

 Connect the middle secon tension cable (39) to the bracket of

lower secon cable tension (35) (See gure A1-A3). Before this step

of the installaon, it is advisable to adjust the resistance seng to the

hardest stage 10, at which the cable extends furthest from the sheath.

Put the lowest part of cable (39) into the small hook (gure A1). Pull it

unl the small hook get in higher posion (A2) and then insert the ca-

ble (39) onto the bracket (35) (gure A3).

 Put one spring washer (32) and one curved washer (31) on each

screw (33). Push the screws (33) through the holes in the support (30),

screw into the threaded holes of the main frame (40) and ghten light-

ly.

 Push the plasc cover (101) and rubber ring (100) into the right

posion to cover the connecon point.







 Push the grip axle (19) into the middle

posion at handlebar support (30) and put

one wave washer (20) and the connecng

tube (25R) onto the axles’ end (19). Put on

the hex screw M8x20 (12) a spring washer

(32) and a washer 8//32 (22) and ghten it

rmly.

 Put the foot pedal holder (44R) at the

pedal crank (97) and ghten them with steel

tube (52), washer 8//20 (49), spring washer

(32) and screw M8x20 (48) rmly.

 Install the le footrest holder (44L) incl.

all addionally required parts on the le

hand side of the machine as described in 1.

– 7.

 Put the plugs of pulse cables (10) into

the plugs from pulse connecon cables (16)

and aach the screw caps (11) onto screws

(12).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Christopeit CRT 7100 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info