Bedienungsanleitung Christopeit CX3 - 1531 (Seite 18 von 56) (Deutsch, Englisch, Holländisch, Französisch)

644104

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Step 3:

Attach the footrest holder (5) at the connecting tubes (6).

1. Put the holder of footrest holder left (5L) at lower end of

connecting tube left (6L) and adjust the holes in the tubes so

that they are aligned.

2. Push the bolts M8x55 (30) through the holes and tighten the

footrest holder left (5L) at connection tube left (6L) with washer

8//16 (31) and nut M8 (32) ﬁrmly. (This connection point has to

move easily. So please don’t tighten the screw too much.)

3. Install the footrest holder right (5R) incl. all additionally required

parts on the right hand side of the machine as described in 1. – 2.

4. Push the screw caps M8-14 (23) onto the screw head of screw

(30) and the screw caps M8-13 (57) onto the nuts (32).

Step 4:

Attach the footrest holder (5) and connecting tubes (6).

1. Place the preassembled unit of the right footrest holder (5R) and

connecting tube right (6R) at the right hand side of the main frame

(1). (Note: Right is speciﬁed as viewed standing on the machine

during training.)

2. Put the axle (27) into the center of support (2) and push the wave

washer (54) onto the axle (27).

3. Push the connection tube right (6R) onto the axle (27) an put on

the screw M8x15 (24) a spring washer for M8 (52) and a washer

8//32 (25) and tighten it ﬁrmly. Push the screw cap M8-14 (23)

onto the screw head of screw (24).

4. Place the footrest holder right (5R) near to the pedal crank (22).

Put onto the axle’s screw right (38R) a wave washer (62) and

screw the foot pedal holder (5R) at the pedal crank (22) ﬁrmly.

Step 5:

Attach the foot pedal (10) at the footrest holder (5).

1. Push the right footrest (10R) onto the right footrest holder (5R).

Adjust the holes in the parts so that they are aligned.

2. Push the screws M10x45 (33) from above through the holes.

Push on a washer 10//20 (34) from the opposite side, screw on

a nut M10 (35) and tighten ﬁrmly.

3. Install the left footrest (10L) on the left footrest holder (5L) as

described in 1.– 2. (Note: The right and left footrests can be

discerned by the edges of the longitudinal sides of the footrests.

The high edges of the footrests (10L+10R) must point inwards

(towards the main frame (1).))

4. Push the screw caps M10 (36) onto the screw head of screw (37)

and nuts (35).

Finally tighten them with spring washer (41) and self locking nut

right (42R) ﬁrmly. Then put a screw cap ½” (43) onto the nut

(42R).

(Note: The screws (38L&R) are marked with “L” for left and “R”

for right. Please use appropriate nut for left and right screw. On

right side the axle screw and nut have to screw clock wise.)

5. Install the left footrest holder left (5L) incl. all additionally required

parts on the left hand side of the machine as described in 3. – 4.

(Note: The screw direction on left side for axle screw and nut is

anti-clock wise.)

6. Now cycle 3-4 movements carefully by hand and tighten the

pre-connected screws (16) of step 2 ﬁrmly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Christopeit CX3 - 1531 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info