Bedienungsanleitung Christopeit Delta 1505 (Seite 24 von 60) (Deutsch, Englisch, Holländisch, Französisch)

656860

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Training area in mm

(for home trainer and user)

Free area in mm

(Training area and security area

(rotating 60cm))

Cleaning, Checks and Storage of the Ergometer

bike:

1. Cleaning

Use only a less wet cloth for cleaning. Caution: Never use benzene,

thinner or other aggressive cleaning agents for surface cleaning as

this damage caused.

The device is only for private home use and for use suitable indoors.

Keep the unit clean and moisture from the device.

2. Storage

Plug out the power supply unit while intending the unit for more than

4 weeks not to use. Push the saddle slide toward the handlebar and

the seat support tube as deeply as possible into the frame. Choose

a dry storage in-house and put some spray oil to the pedal bearings

left and right, to the thread of the handlebar bolt, and on the thread

of the quick release for saddle support.

Cover the bike to protect it from being discolor by any sunlight and

dirty through dust.

3. Checks

We recommend every 50 hours to review the screw connections for

tightness, which were prepared in the assembly. Every 100 operating

hours, you should put some spray oil at the pedal bearings left and

right, to the thread of the handlebar bolt and to the thread of quick

release for saddle support.

Troubleshooting

If you cannot solve the problem with the following information,

please contact the authorized service center.

Problem Possible Cause Solution

Computer has

no value at Dis-

play if you press

any key.

No power

adapter is well

plugged or wall

power is without

power.

Check that the power adapter

is properly plugged in, possibly

with another electric device

check if the wall power is ﬁne.

Computer is

not counting

data and do not

switch on after

start cycling.

Sensor impulse

missing base on

not well plugged

connection

Check the plug connections at

computer and inside of handle-

bar support.

Computer is

not counting

data and do not

switch on after

start cycling.

Sensor impulse

missing base on

not correct posi-

tion of sensor.

Take off the cover and check

the distance between magnet

and Sensor. The magnet at

turning belt wheel should have

only less than < 5mm distance

against the sensor position.

No pulse value Pulse cable is

not plugged in.

Check the separately pulse

cable is well connected with

computer.

No pulse value Pulse sensors

not well connec-

ted

Screw out the screw for pulse

measurement and check if

plugs are well connected and no

damage at pulse cable.

gently both metal parts each hand. With the good signals picked up by the

computer, the heart symbol in the HEART RATE Display shall ﬂash. Some-

times the heart rate value is not useable, based on wet hands or any other

contact problems during exercising. If you need high accuracy heart rate

value, you have to use an external heart rate measurement with a pulse

belt and pulse watch.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Christopeit Delta 1505 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info