Bedienungsanleitung Christopeit Omega (Seite 21 von 60) (Deutsch, Englisch, Holländisch, Französisch)

602836

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Step 3:

Installation of the pedal supports (32) with connecting tubes (19) and

pedals (38).

1. Place the handgrip axle (7) in the holder of handlebar support (10) and

push on each side one wave washer 17//25 (8) on axle’s end.

2. Place the preassembled unit of foot pedal support right (32R) and

connection tube right (19R) on right side next to the main frame and

push the smaller wave washer onto the pedal crank (70) on right side.

3. Push the connecting tube (19R) onto the handgrip axle (7) and the

pedal support holder (97R) onto the pedal crank (70) at the same time.

Put on the screw (23) a spring washer (28) and a big washer 8//38 (24)

and tighten the connection tube (19R) at hand grip axle (7) ﬁrmly. Then

tighten the pedal support holder (19R) at pedal crank (11) with screw

(23), spring washer (28) and a little bit smaller washer 8//28 (101).

4. Install the left pedal support left (32L) with connection tube (19L) incl.

all additionally required parts on the left hand side of the machine as

described in step 2-3.

5. Mount front pedal support cover (35L+35R) to both side front ends of

pedal supports (32L+32R) and secure with screws (33+34) each side.

6. Turn the assembled unit at pedal crank slowly for 3-4 rotations and

tighten now the screw connection of handlebar support of Step 2 ﬁrmly.

Push down the handlebar support cover (51) to cover up the screw

connection.

7. Put the pedals (38L+38R) onto the pedal holders (32L+32R). Adjust the

holes in the parts so that they aligned.

8. Push the screws (41) from above through the holes. Put on a washer (40)

from the opposite side and screw on a hand grip nut (39) and tighten

ﬁrmly. (Note: The right and left footrests (38) can discern by the edges

of the longitudinal sides of the footrests. The high edges of the footrests

(38) must point inwards (towards the main frame. The position adjusted

in this way should always be equal at both sides. The positions can

change as desired at all times by removing the carriage bolts (41) and

sliding the footrests on the footrest brackets to get a more or less ﬂat

movement.)

Step 4:

Installation of the handgrips (29) at the connecting tubes (19).

1. Put the handgrip bars (29L+29R) onto the connecting tubes (19L+19R)

and adjust the holes in the tubes so that they are aligned.

(Note: the handgrip bars must be aligned after assembly so that the

upper ends are inclined outwards (away from the support (10)).

2. Put on each bolt (21) a curved washer (3) and push the bolts (21) through

the holes and tighten the handgrip bars (29L+29R) at connection tubes

(19L+19R) with nut (27) ﬁrmly.

3. Place the bottle holder (5) into the appropriate position of handlebar

support (10) and ﬁx it with two screws (4).

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Christopeit Omega Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info