Bedienungsanleitung Christopeit POWER XL 1582 (Seite 17 von 56) (Deutsch, Englisch, Holländisch, Französisch)

793219

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

English

Assembly Instructions

Before beginning assembly, be sure to observe our recommendations

and safety instructions.

Several items are pre-assembled. Assembly time: 55 - 65 min.

Step 1:

Connecting the rear feet (1) to the crossframe (2) with the reinforcing

plates (59), the hexagonal bolts M10x70mm (38), the washers (52) and

the self-locking nuts M10 (49).

1. Place the rear feet (1), the crossframe (2), the screws (38), the washers

(52) and the nuts (49) accessibly.

2. Push one washer (52) onto each of the screws (38) and push from the

outside through the reinforcing plates (59) through the two rear feet

(1).

3. Join the crossframe (2) with the holes over the inserted screws so that

the longitudinal frame holder faces forwards and connect the whole

assembly by pushing on the washers (52) and lightly screwing on the

nuts (49).

4. Then tighten the previously made bolted connection ﬁrmly and mount

the securing clips left (60) and right (61) with the washers (54) and the

self-locking nuts (62) on the Barbell rack (7).

5. Push the barbell rack (7) into the matching locator in the rear foot (1),

set it at the desired position and lock it by inserting the bolt with the

quick release (6) in place and doing it up tight. (The setting of the barbell

rack (7) can adjusted easily as desired later through turning and pulling

the quick release (6).) Furthermore, you must ensure when setting this

desired position that the barbell rack (7) is not pulled out of the main

frame further than the highest setting position, which is marked.

Attention: Ensure before every exercising that the barbell rack (7) is

tighten ﬁrmly. With safety clips (60+61) you can secure the barbell on

the barbell rack (7) to avoid drop off the barbell during loading the

weight plates.

Step 2:

Connecting the front foot (8) and the crossframe (2) to the longitudinal

frame (3) with hexagonal screws (39) + (40), washers (52) and the self-

locking nuts (49).

1. Place the front foot (8), the longitudinal frame (3), the screws (40), the

washers (52) and the nuts (49) accessibly.

2. Push a washer (52) onto each screw M10x25 (40) and push these from

the front through the front foot (8).

3. Join the longitudinal frame (3) with the holes over the inserted screws

and connect by pushing on the washers (52) and loosely screwing on

the nuts (49). Then tighten the bolted connection.

4. Insert the longitudinal frame (3) in the crossframe (2) so that the last

hole but one in the longitudinal frame (3) corresponds with the last

hole in the crossframe (2). Push a washer (52) onto the screw M10x60

(39) and push through the overlapping holes. Push a washer (52) onto

the end of the screw ant screw on the nut (49) until the self-locking

part of the nut engages on the thread of the screw (39) and the folding

mechanism is not blocked.

Step 3:

Installation of the crossbar (11) with the front foot (8) and the longitudinal

frame (3) with the hexagonal screws (41) + (48), washers (53) and nuts

(50).

1. Place the crossbar (11) with the screws (41) + (48), the washers (53)

and the nuts (50) accessibly.

2. Place a washer (53) on each of the screws (41) + (48). Hold the crossbar

with the hole over the fastening point on the front foot (8) and screw

on loosely with the screw (41). Note: The crossbar (11) must properly

mounted to the connection points.

3. Align the crossbar (11) with the second hole over the fastening point

on the longitudinal frame (3) and fasten loosely with the screw (48), the

washers (53) and the nut (50).

4. Then tighten the loosely made bolted connection.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Christopeit POWER XL 1582 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info