Bedienungsanleitung Christopeit R 10 - 9917 (Seite 17 von 44) (Deutsch, Englisch, Holländisch, Französisch)

517231

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

English

Computer instructions for 9917

The supplied computer allows the most convenient training. Every value

relevant to training is displayed in a corresponding window.

From the beginning of the training session, the required time, the current

speed, the approximate calorie consumption, the travelled distance ad

the current pulse rate are displayed. All values are counted from zero

upwards.

The speed is indicated on the upper display. All other values are indicated

on the lower display.

If you wish to see one value displayed constantly as well as the speed during

training, select this with the „F“ key. If you wish to see these values in constant

alternation, select the „SCAN“ function. The display then changes from one

function to the next at intervals of approx. 6 seconds.

The computer is switched on by brieﬂ y pressing the F- key or simply by

beginning training. The computer begins to register and display all values.

To stop the computer, just stop training. The computer stops all measurements

and retains the last attained values. The last attained values in the functions

TIME, CALORIES and KM are stored and training can continue with these

values when training is resumed.

The computer switches of automatically approx. 4 minutes after training is

stopped. All values attained until that time are stored and are displayed again

when training is resumed. It is then possible to continue training from these

values or to reset all functions to zero using the L- key.

Displays:

1. „SPEED“ display:

The current speed is displayed in kilometres per hour. It is not possible to

specify a particular value using the „E“ key. The values last attained by this

function are not stored. (Limit of the display: 99.9 km/h.)

2. „TIME“ display:

The currently required time is displayed in minutes and seconds. It is possible

to specify a particular value using the „E“ key. If a particular time

has been speciﬁ ed, the remaining time is displayed. When the speciﬁ ed value

is attained, this is indicated by an acoustic signal. The values last attained

by this function are stored. (Limit of the display: 99.59 minutes.)

3. „DIST“ display:

The current status of the travelled distance is displayed. It is possible to

specify a particular value using the „E“ key. If a particular distance has been

speciﬁ ed, the remaining distance is displayed. When the speciﬁ ed value is

attained, this is indicated by an acoustic signal. The values last attained by

this function are stored. (Limit of the display: 999 km.)

4. „CALORY“ display:

The current status of the consumed calories is displayed. It is possible to

specify a particular value using the „E“ key. If a particular consumption

has been speciﬁ ed, the remaining number of calories to be consumed is

displayed. When the speciﬁ ed value is attained, this is indicated by an

acoustic signal. The values last attained by this function are stored. (Limit

of the display: 999 calories.)

5. „ODO“ display:

The current status of the travelled kilometres of all previous training sessions

including current training session is displayed. A particular value cannot be

speci. ed. The values last attained by this function are not stored. (Limit of

the display: 9.999 km.)

6. „PULSE“ display:

The current pulse rate is displayed in beats per minute. It is possible to specify

a particular value using the „E“ key.

If a particular upper pulse rate limit has been speciﬁ ed, an acoustic signal

will indicate if these limits are infringed.

The values last attained by this function are not stored. (Limit of both displays:

40 – 240 pulse beats per minute.)

Note:

For pulse measurement, the two contact surfaces of the pulse measuring

handle unit (62) must be gripped simultaneously. The contact surfaces should

be located centrally in the palms of the hands.

7. „SCAN“ function:

If this function is selected, the current values of all functions are displayed

successively in a constant sequence approx. every 5 seconds.

Keys:

1. „F“ key:

Pressing this key once brieﬂ y makes it possible to change from one function

to another, i.e. the respective functions can be selected for which entries

can be made using the „E“ key. The currently selected function is indicated

by an icon in the respective window.

2. „E“ key:

By pressing this key once, it is possible to specify values step by step in the

respective functions. For this, the desired function must ﬁ rstly be selected

using the „F“ key.

Holding the key pressed activates faster running, which can be stopped by

pressing the key again. When training begins, the speciﬁ ed values are then

counted down to zero.

3. „L“ = Delete:

When this key is pressed brieﬂ y, the values chosen with the „F“ key are

reset to zero. If the key is held longer (approx. 3 seconds), all last attained

values are deleted with the exception of the values in the „KM TOTAL“

display.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Christopeit R 10 - 9917 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info